GSC21KGRW GE Refrigerator Parts List

Water tank assembly (water tank in refrigerator for chilled water dispenser)

This tank stores water until the water actuator is activated and water is requested.

Union connector - 5/16 inch to 5/16 inch (quick connector for refrigerator water line, 5/16 to 5/16 inches.)

Quick connector for plastic water line - 5/16" to 5/16"

Run capacitor (refrigerator run capacitor 12 uf. If this run capacitor is defective, the refrigerator will not run.)

The run capacitor is attached to the compressor and is 12 UF. It helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer. If your refrigerator is too warm, will not start, or your freezer section is too warm, you may need to replace this part. This is a genuine OEM part. Please remember to disconnect power to your refrigerator before starting your repair.

Mwf manifold (mwf water filter housing assembly with by-pass)

Dispenser door recess crank (dispenser door crank)

The door recess crank for your refrigerator is located inside the water dispenser assembly. To access this part, you will need to take apart the dispenser assembly. To do this, you will need a putty knife and a Phillips screwdriver. If your dispenser door will not close properly, or ice is not dispensing properly, you may have a damaged door recess crank. This part is made of white plastic and is sold individually.

Shelf stop - white (stop shelf)

The shelf stop in your refrigerator is what locks the shelf into the refrigerator liner. The shelf stop can be found attached to the shelf. To remove the shelf stop, begin pulling the shelf out until the stop hits the refrigerator liner, then depress the shelf stop to remove the shelf. With the shelf removed, you can simply slide the old stop out of its groove, and replace it with a new one. This part is made of white plastic and is about 1 inch in length. It is sold individually, and is an OEM part sourced directly from the manufacturer.

Wheel pan cover

Screw (screw 10-16 pl pnp 5/8 szn)

10-16 pl pnp 5/8 szn - Sold individually.

Evaporator fan blade

This evaporator fan blade is for your refrigerator, and it circulates air so that the temperature of the fridge is regulated. This model has 3 blades, and is a little more than 4 inches in diameter. It is made of white plastic and is sold individually. If your refrigerator is noisy and you hear a clicking sound, it is a good indication that the evaporator fan blade is warped or damaged. If the fridge or freezer sections become too warm, the fan could be to blame as well.

Dispenser housing shield (housing shield disp)

This part helps to contain parts for the ice and water dispenser. The overlay and dispenser board is attached on the front of the housing shield.

Front dispenser bucket auger nut (nut, auger, front dispenser bucket.)

Coarse thread

Crisper pan front gasket (gasket pan crv front)

This part is a replacement pan cover gasket for your refrigerator. You will find the pan cover gasket on the meat pan, and it helps to seal the pan. If the pan cover gasket is lost or damaged, it will not be able to create the seal and will need to be replaced. The gasket is approximately 15 inches wide and is white in color. It is an OEM part from the manufacturer and is sold individually.

Recess grille (dispenser tray, black)

This part is a replacement recess grille tray for your refrigerator. This recess grille tray sits below the ice and water dispenser, and collects any spills. If your dispenser grille tray is broken or missing, this is the part that replaces it. This part is made of black plastic and is approximately 7 inches wide. It is sold individually and is an OEM part from the manufacturer.

Air inlet cover kit (refrigerator air inlet cover/damper kit with fan motor. Damper and fan assembly have been updated to prevent freezing food in the refrigerator.)

This kit includes damper, fan assembly, nozzle and gasket for nozzle. The damper and fan has been updated by the manufacturer to avoid freezing in the refrigerator. Also known as a damper assembly.

Auger motor (refrigerator ice dispenser auger motor. The auger motor pushes the ice through the dispenser chute. If the auger motor is defective, the ice won’t fa)

This motor is used to activate the blades to crush the ice for dispensing. This part is now threaded with a left hand thread and the J nut is no longer required.