GSC22QGTW GE Refrigerator Parts List

Evaporator fan grommet - grey (grommet for an evaporator fan)

This is a replacement evaporator fan grommet for your refrigerator. The fan grommet absorbs the vibration from the evaporator fan motor for quiet operation while it runs. If your evaporator fan is unusually noisy, it could be because the grommet is damaged. This grommet is made of grey plastic and is approximately one inch in diameter. To access the fan grommet and complete this repair, you will need to remove the evaporator fan motor assembly. This part is sold individually.

Shelf support (support shelf)

This plastic shelf support, or shelf stud connects the shelf to your refrigerator. To replace the shelf support first remove the shelves and drawers from your refrigerator, then remove the damaged or faulty stud before installing the new one. This genuine OEM shelf support has an outside diameter of approximately half an inch.

Dc condenser fan motor - 12v (condenser fan motor, 12 volt dc motor. *if you need 120 volt motor see item #1257132)

This fan motor circulates the air through the refrigerator grille and cools the compressor and condenser coils. It also helps to evaporate extra water in the drain pan.

Mwf bypass (cap, water filter bypass)

This part is a replacement filter bypass cap for your refrigerator. If you intend to use an external water filtration system for your refrigerator, the bypass cap will allow you to do so. To use a filter bypass cap, simply screw it in where you would normally screw in the regular water filter. If you have a bypass system installed and your ice maker doesn’t make ice, your water dispenser doesn’t make water, or if there is water dripping inside your refrigerator, you may need to replace the bypass filter cap. This part is made of white plastic and is sold individually.

Humidity control - white (humidity control, white)

This part regulates the humidity of your crisper bins. It does so by opening and closing vents on the bin. If your humidity control is broken or missing, you will need to replace it. This is a genuine OEM part from GE and is sourced directly from the manufacturer.

Handle (drawer handle)

Ice dispenser solenoid service kit (ice crusher solenoid plunger)

This kit includes 1 cube solenoid, 1 armature, 2 tooth washers and 2 1/4 hex head screws.

Screw - 12-24 tt ovt .900 s (screw)

Sold individually.

Micro switch

This is the replacement micro switch, or dispenser switch for your refrigerator. It is gray in color and measures approximately 1 inch by half an inch. The dispenser switch is what tells your refrigerator that it is ok to dispense ice or water. If your refrigerator is not dispensing ice or water, you may have a faulty or damaged switch. Be sure to disconnect the power to your refrigerator before you begin this repair. This switch is sold individually and is a genuine OEM replacement part sourced directly from the manufacturer.

Drawer slide rail bracket - left side (glide bracket lh)

This is the replacement drawer side rail for the left side of your refrigerator. It is made of white plastic and is approximately 12 inches long, and 2 inches wide. The slide rail supports the crisper drawer as it slides in and out. If the slide rail is broken, you may have difficulty sliding the drawer in and out. This rail is for the left side of the drawer, and the slide for the right side is sold separately. This part is sold individually and is and OEM part.

Grommet / tube assembly (icemaker fill tube assembly)

This is a replacement fill tube and grommet assembly for your refrigerator. This part acts your water line to your ice maker. If you’re noticing water in the back of the refrigerator or any kind of leak, or if your ice bucket isn’t filling up with as much ice, you may need to change out the fill tube and grommet assembly. When you purchase this part, you get the water line, as well as the fill tube and grommet. This is an OEM part sourced directly from the manufacturer.

Auger (auger asm disp)

This ice bucket auger is a genuine OEM replacement part for your refrigerator freezer section. The auger rotates and separates the ice in the bucket. To replace it, start by pulling out the ice bucket assembly. Remove the cover, shield, and actuator arm bracket using a Phillips head screwdriver. Unhook the spring holding the arm in place to remove the arm. Use your screwdriver to pry off the e-clip and washer. Use a wrench to detach the auger from its housing. This part includes the auger only, not the assembly or housing.

Housing crusher dispenser (housing crusher disp)

Refrigerator deli drawer (middle drawer assembly)

The deli drawer holds meats, vegetables and snacks in the fresh food compartment of the refrigerator.

Torsion-fit spring (return spring for dispenser funnel)

This part is the replacement torsion-fit spring for your refrigerator. It is made of metal and is sold individually. The torsion-fit spring provides tension to return the ice funnel back to its normal position after it dispenses ice. If your refrigerator is not dispensing ice or water properly, you may need to replace the torsion-fit spring. This is an OEM part sourced directly from the manufacturer.