GSC23KSTS GE Refrigerator Parts List

Shelf stop - white (stop shelf)

The shelf stop in your refrigerator is what locks the shelf into the refrigerator liner. The shelf stop can be found attached to the shelf. To remove the shelf stop, begin pulling the shelf out until the stop hits the refrigerator liner, then depress the shelf stop to remove the shelf. With the shelf removed, you can simply slide the old stop out of its groove, and replace it with a new one. This part is made of white plastic and is about 1 inch in length. It is sold individually, and is an OEM part sourced directly from the manufacturer.

Wheel pan cover

Icemaker stripper arm (ice stripper for rear mount icemaker, about 7 inches long)

This part strips the ice from the icemaker mold during the ejection cycle. Used on rear mount icemakers.

Evaporator fan blade

This evaporator fan blade is for your refrigerator, and it circulates air so that the temperature of the fridge is regulated. This model has 3 blades, and is a little more than 4 inches in diameter. It is made of white plastic and is sold individually. If your refrigerator is noisy and you hear a clicking sound, it is a good indication that the evaporator fan blade is warped or damaged. If the fridge or freezer sections become too warm, the fan could be to blame as well.

Front dispenser bucket auger nut (nut, auger, front dispenser bucket.)

Coarse thread

Crisper pan front gasket (gasket pan crv front)

This part is a replacement pan cover gasket for your refrigerator. You will find the pan cover gasket on the meat pan, and it helps to seal the pan. If the pan cover gasket is lost or damaged, it will not be able to create the seal and will need to be replaced. The gasket is approximately 15 inches wide and is white in color. It is an OEM part from the manufacturer and is sold individually.

Recess grille (dispenser tray, black)

This part is a replacement recess grille tray for your refrigerator. This recess grille tray sits below the ice and water dispenser, and collects any spills. If your dispenser grille tray is broken or missing, this is the part that replaces it. This part is made of black plastic and is approximately 7 inches wide. It is sold individually and is an OEM part from the manufacturer.

Air inlet cover kit (refrigerator air inlet cover/damper kit with fan motor. Damper and fan assembly have been updated to prevent freezing food in the refrigerator.)

This kit includes damper, fan assembly, nozzle and gasket for nozzle. The damper and fan has been updated by the manufacturer to avoid freezing in the refrigerator. Also known as a damper assembly.

Evaporator fan grommet - grey (grommet for an evaporator fan)

This is a replacement evaporator fan grommet for your refrigerator. The fan grommet absorbs the vibration from the evaporator fan motor for quiet operation while it runs. If your evaporator fan is unusually noisy, it could be because the grommet is damaged. This grommet is made of grey plastic and is approximately one inch in diameter. To access the fan grommet and complete this repair, you will need to remove the evaporator fan motor assembly. This part is sold individually.

Shelf support (support shelf)

This plastic shelf support, or shelf stud connects the shelf to your refrigerator. To replace the shelf support first remove the shelves and drawers from your refrigerator, then remove the damaged or faulty stud before installing the new one. This genuine OEM shelf support has an outside diameter of approximately half an inch.

Mwf bypass (cap, water filter bypass)

This part is a replacement filter bypass cap for your refrigerator. If you intend to use an external water filtration system for your refrigerator, the bypass cap will allow you to do so. To use a filter bypass cap, simply screw it in where you would normally screw in the regular water filter. If you have a bypass system installed and your ice maker doesn’t make ice, your water dispenser doesn’t make water, or if there is water dripping inside your refrigerator, you may need to replace the bypass filter cap. This part is made of white plastic and is sold individually.

Humidity control - white (humidity control, white)

This part regulates the humidity of your crisper bins. It does so by opening and closing vents on the bin. If your humidity control is broken or missing, you will need to replace it. This is a genuine OEM part from GE and is sourced directly from the manufacturer.

Ice bucket and auger assembly (bucket and auger asm)

This assembly includes the auger, bucket, cutting assembly (blades) and cover.

Freezer door gasket - black (freezer door gasket, black)

This door gasket is used to seal the freezer door when closed.

Ice dispenser solenoid service kit (ice crusher solenoid plunger)

This kit includes 1 cube solenoid, 1 armature, 2 tooth washers and 2 1/4 hex head screws.