GSE23GGKNCBB GE Refrigerator Parts List

Temperature sensor (sensor temperature)

The temperature sensor, also known as a thermistor, helps detect the temperature inside the refrigerator and sends the information to the control board. If your refrigerator is too warm or not cooling properly, you may need to replace the temperature sensor. This is a genuine OEM part. Please make sure to disconnect the power to the refrigerator before starting your repair.

Module shelf insert - clear (insert module)

This part is the front of the door shelf bin.

Evaporator fan grommet - red (grommet evap fan)

This red evaporator fan motor grommet provides a cushion between the fan motor and the motor mounting bracket. If the grommet is damaged and you are getting noise from the fan motor, you may need to replace it. This is an OEM part sourced directly from the manufacturer. Please remember to disconnect the power to the refrigerator before starting your repair.

Dispenser door solenoid assembly (solenoid asm)

This part is a possible option when ice door won't open or shut properly or when water is not dispensing.

Dispenser door assembly or flapper (door recess asm)

The ice chute door opens to dispense ice once activated. This part mounts in the ice dispenser. If it is too warm inside your refrigerator, there is frost build up, or your icemaker will not make or dispense ice, you may need to replace the ice chute door. The crank no longer comes with this part, but you can use the original crank. The crank is sold separately depending on the model number of your appliance. The ice chute door is a genuine OEM part. Please remember to disconnect the power to the refrigerator before starting your repair.

Middle pan cover frame - no glass (cover middle pan)

This is the frame only. Glass is NOT included and must order separately.

Middle crisper pan (pan middle asm)

Fruits and vegetable drawer.

Compression ring (ring compression)

The compression ring works for a variety of fans throughout your refrigerator, the evaporator fan or condenser fan. If you notice your refrigerator or freezer is too warm, or there is an unusual sound during operation you may need to replace the compression ring. This part is made of metal, measures approximately 0.25” L x 0.5” in diameter, and is sold individually. This is a genuine OEM part. Please remember to disconnect the power before starting your repair.

Lid bumper (bumper)

This orange rubber bumper prevents the condenser fan motor from bumping against the mounting bracket every time the fan motor starts. If your refrigerator/freezer is noisy, the bumper could be worn down or missing, and the sound could be a result of the motor scraping the side bracket. You will find it between the fan motor and the side bracket on the evaporator fan motor assembly. It has a rounded top and a slightly pointed bottom. The bumper is a genuine OEM part and is sold individually.

Light switch (switch light)

This is the light switch that goes in your refrigerator. If the light is not working or stays on, you may need to replace the switch. It is made of mainly white plastic, and is an OEM part, directly from the manufacturer. Be sure to disconnect the refrigerator from the power source before you begin this repair. To remove the switch, simply use a flathead screwdriver to pop the switch out from the refrigerator wall, then disconnect the wires. Reconnect the wires to the new switch, snap it into place, and the repair is complete.

Water tank assembly (water tank disp asm)

This tank stores water until the water actuator is activated and water is requested.

Union connector - 5/16 inch to 5/16 inch (union connector)

Quick connector for plastic water line - 5/16" to 5/16"

Shelf stop - white (stop shelf)

The shelf stop in your refrigerator is what locks the shelf into the refrigerator liner. The shelf stop can be found attached to the shelf. To remove the shelf stop, begin pulling the shelf out until the stop hits the refrigerator liner, then depress the shelf stop to remove the shelf. With the shelf removed, you can simply slide the old stop out of its groove, and replace it with a new one. This part is made of white plastic and is about 1 inch in length. It is sold individually, and is an OEM part sourced directly from the manufacturer.

Wheel pan cover

Pan cover glass (cover pan glass)

Glass only. Frame sold separately.