GSS25LGPC GE Refrigerator Parts List

Refrigerator ice and water filter (ice and water filter)

Ice maker (refrigerator icemaker kit, the kit includes the fill cup, 4 pin wire harness adapter, and tube.)

This ice maker assembly is used to make ice in your refrigerator. The ice maker receives water from the water inlet valve and will freeze until ice cubes are formed. Once the water has been frozen the cubes will be ejected from the mold into the ice bucket. The ice maker will continue the process until the ice bucket has reached the limit. If your ice maker is not making ice you may need to replace this part. This kit includes the fill cup, 4-pin wire harness adapter, and a tube. Disconnect the power and water supply before starting your repair. This ice maker is a genuine OEM part.

Water valve with guard (refrigerator water inlet valve assembly with quick connect fitting . To disconnect the tube, push the white retainer fitting in while pulling on the)

This double inlet water valve has quick connections. This valve has 1/4 and 5/16 John Guest fittings for the outlet lines and a 1/4 compression fitting for the inlet line.

Temperature sensor (refrigerator or freezer temperature sensor (also called a thermistor).)

The temperature sensor, also known as a thermistor, helps detect the temperature inside the refrigerator and sends the information to the control board. If your refrigerator is too warm or not cooling properly, you may need to replace the temperature sensor. This is a genuine OEM part. Please make sure to disconnect the power to the refrigerator before starting your repair.

Module shelf insert - clear (door shelf front, clear)

This part is the front of the door shelf bin.

Defrost thermostat (high limit thermostat for refrigerator or freezer defrost heater, l140-30f. This thermostat is normally closed for continuity at room temperature.)

This defrost thermostat acts as a safety device against over heating in case of mechanical failure.

Ice dispensing drive cup (drive cup, ice dispensing bucket)

This part is found at the end of the auger in the ice container - replace this part when the icemaker doesn't dispense ice.

Dispenser door solenoid assembly (refrigerator solenoid assembly for dispenser door. If the dispense door does not close properly frost will start to form in the dispenser area.)

This part is a possible option when ice door won't open or shut properly or when water is not dispensing.

Dispenser door assembly or flapper (refrigerator ice dispenser damper door. The crank is no longer sold with the damper door. You will have to reuse the old crank.)

The ice chute door opens to dispense ice once activated. This part mounts in the ice dispenser. If it is too warm inside your refrigerator, there is frost build up, or your icemaker will not make or dispense ice, you may need to replace the ice chute door. The crank no longer comes with this part, but you can use the original crank. The crank is sold separately depending on the model number of your appliance. The ice chute door is a genuine OEM part. Please remember to disconnect the power to the refrigerator before starting your repair.

Defrost heater and bracket assembly (refrigerator defrost heater and bracket assembly.)

The defrost heater keeps the cooling coils from frosting over. The heater will get hot and melt any ice or frost build up around the coils.

Dispenser light (refrigerator light bulb for the dispenser, 12 volts.)

This twelve volt dispenser light bulb is a little under two inches long.

Evaporator fan motor (refrigerator evaporator fan motor. If your motor has a white thermistor in the connector you need the related fan motor 914169. If it has a connector)

This evaporator fan motor is located in the back of the freezer, and circulates air over the refrigerator coils. These coils will convert the heat into cool air, which is then circulated. Note: Thermistor is NOT included. If you need the motor with the thermistor, see related parts.

Recess door spring (spring, recess door)

This door recess spring or dispenser lever spring in your refrigerator is used to return the ice door to the closed position or the dispenser lever to the home position once released. You will find the spring in the water dispenser assembly, behind the main control panel. If the dispenser lever is malfunctioning or the dispenser ice door is not closing, you may need to replace this door recess spring.

Refrigerator door shelf bin

Sold individually. This door bin is for refrigerators. Door bin attaches to the inside of the refrigerator door and typically holds jars and bottles. Follow the instructions in the owner's manual for installing this part.

Ice bucket and auger assembly (ice bucket and auger assembly complete.)

This part holds the ice once it's released from the icemaker. When activated, the auger rotates and pushes ice out of the bin through the chute to the user.