L3B345GL0 GE Range Parts List

Bake element (oven bake element. The terminals are male quarter inch spade connectors. The wires push onto the heating elements connectors.)

This partially open-style bake element comes with ¼-inch push-on terminals and is located on the bottom of the oven. This bake element provides heat for baking. If your oven is too hot, not heating evenly, the element is not heating, or has little to no heat when baking, you may need to replace your bake element. You can use a multi meter to test the bake element for electrical continuity to see if you need to replace it. This is a genuine OEM part. Please remember to disconnect the power to the range before starting your repair.

Drip bowl - 6 inch (chrome drip bowl for 6-inch burner on electric range. This drip bowl sits underneath the burner to catch drips or spills.)

This six-inch chrome drip bowl is intended for use with rolled terminal-style plug in surface element units. The drip bowl sits under the burner to catch anything that may spill over to make cleaning up spills quick. This is a genuine OEM part and is sold individually.

Drip bowl - 8 inch (chrome drip bowl (pan) for 8-inch burner on electric range. This drip bowl sits underneath the heating element to catch drips or spills.)

The chrome drip bowl is located under the burner element to catch anything that may spill over to make cleaning up spills quick. This drip bowl is eight inches in size and is intended for use with rolled terminal style plug-in surface element units. This is a genuine OEM part and is sold individually.

Infinite heat switch kit (stove top surface element control switch kit. If the surface element is not heating the element can be tested to determine if it is defective.)

The infinite switch controls the stove top surface burner. This switch will work with most of the electrical range models with coil burner elements.

Single heating element support clip (support bracket for oven broil element.)

The support clip is used to hold the broil element in place at the top of the oven cavity. If the clip is broken or damaged, you will need to replace the part. The support clip is made of metal, is a little over an inch long, and is sold individually. This is a genuine OEM part.

Oven sensor (oven temperature sensor assembly. The oven sensor works in conjunction with the oven control board to regulate the oven temperature.)

The temperature sensor, also known as an oven probe, detects the temperature within the oven cavity. This temperature sensor is a genuine OEM part. If your oven is too hot, not heating evenly, has little to no heat when baking, or is flashing F3/F4 error messages on your control board, you may need to replace it. Make sure to disconnect the power to your range before starting your repair.

Surface burner terminal block kit (surface burner element terminal block with mounting bracket and wires)

The surface burner terminal block kit comes with a terminal block, wire nuts, heat shrink protective tubing, and wires. This part is used to connect the wire harness to the surface burner element. If your element will not heat at all, or if it is not heating properly, it is likely an issue with the terminal block and it will need to be replaced. This is a genuine OEM part. Please remember to disconnect the power supply before starting your repair.

Hinge with roller - left side (door hinge assembly with roller, left side)

This hinge is located on each side of the oven door

Hinge with roller - right side (door hinge assembly with roller, right side)

This hinge is located on each side of the oven door.

Surface burner - 8 inch - 2100w (8" diameter electric surface element with looped terminal ends)

Broil element - 240v (oven broiler heating element with push-on terminals, 240 volts)

This broil element is found on the roof of the oven and has push-on terminals.

Screw

Sold Individually.

Screw (screw-10-32)

Sold Individually.

Broiler pan - large (broiler pan grill kit, porcelain, includes grill and bottom pan)

The broiler pan and insert allows you to cook on a stable surface while allowing the liquid to drain into the pan below making clean up easier. This part is gray in color, made of enameled porcelain for an easy-to-clean, durable and made to last. The pan measures approximately 17” wide by 13” deep, insert measures 15 1/2” wide by 13” deep. This is a genuine OEM part.

Rear drawer glide (drawer glide, rear)

Also called Rear Block.