LMV1683ST LG Parts List

Filter,grease

The grease filter works in conjunction with microwaves and is used to help collect grease particles in the air from cooking. The grease filter is chrome in color and measures 7 3/4” L x 5” W. This grease filter is sold individually. Most microwaves require two filters, please check your model for correct quantity needed before ordering. This is a genuine OEM grease filte

Light bulb - 120v 30w (lamp,incandescent)

This 30 watt 120 volt incandescent light bulb, with a small screw base is used to light up the surface below your microwave or brighten the interior of the microwave once the door has been opened. If your light bulb is burnt out it will need to be replaced. Before you change the bulb, be sure to check that the light socket still works, as it may need to be replaced as well. Remember to disconnect the power to the microwave before you begin this repair. This is a genuine OEM part and is sold individually.

Glass cooking tray

This tray rotates in your microwave ensuring more even temperatures.

Filter,charcoal

The charcoal filter is used to remove cooking odors from that air that circulates through the vent. It measures approximately 73/4-inch by3/4-inch and is sold individually. This is a genuine OEM part.

Switch,micro

The interlock door switch, also known as a micro switch, will prevent the microwave from operating if the door is open. This switch has been updated by the manufacturer. It may appear different in appearance but will still function as the original part. This part has a green button and measures approximately a little over an inch long. This is a genuine OEM part. Please remember to disconnect the power to the microwave before starting the repair.

Mounting plate (plate,mount)

This mounting plate is a manufacturer-approved replacement part for your microwave. The mounting plate, or bracket, secures your above-range microwave in place against the wall. To conduct this repair, make sure to first disconnect the power source, and wear protective gloves.

Locker

The locker, or door latch assembly fits to the inside of the microwave door, and keeps the door closed. If the door on your microwave oven doesn’t appear to close properly, you may have a problem with the door latch assembly. This locker is made of plastic and measures 7 inches long x 2 inches wide. If either of the hooks is broken or does not have any spring tension, you may need to replace the assembly.

Air duct bracket (bracket,idle)

This bracket holds the metal or plastic flapper that closes off the exhaust duct when the fan is not running and opens when the fan turns on. If the exhaust fan on your microwave does not appear to be working, the problem may be with the damper assembly. If the damper does not open and close easily, check for any damage to the bracket, and replace if it is damaged or faulty. This genuine OEM exhaust damper measures approximately 12 inches long by 5 inches wide.

Damper

The vent damper is used to close off the exhaust duct when the fan is not running, to prevent outside air from entering the microwave. When the fan turns on it allows air to vent away from the microwave. The damper measures approximately 10-inch long by 3-inchwide and is a genuine OEM part.

Holder,cook auxiliary

Switch,micro

This microwave micro switch is normally open and when the door is shut, the door switch will close to send power to the microwave to operate. If the microwave won’t start, then the switch has failed and will need to be replaced. The micro switch is in the latch board section and due to the high voltage capacitor in the microwave, it can retain a lethal electrical charge. Even when unplugged, it is suggested to have a service technician install the part. This is a genuine OEM part.

Turntable assembly

This turntable assembly, also known as a rotating ring, is a genuine OEM replacement part for your microwave. It is brown in color and about 10 inches in diameter. This part supports the glass turntable and keeps it in place. Replacing this part is very easy and requires no tools. Simply remove the glass tray, pop out the existing ring and replace with the new one.

Turntable motor coupler (shaft,turntable)

The turntable motor coupler connects the turntable motor to the tray. If the turntable on your microwave will not rotate, you may have a faulty motor coupler. The coupler commonly has a D shaped opening that fits tightly onto the motor shaft. If it is cracked, or worn it will need to be replaced. This is a genuine OEM replacement part sourced directly from the manufacturer.

Lamp holder

This genuine OEM light socket provides power to the light bulb in your microwave while holding it in place. This light socket is two pronged and the bulb should screw easily into it. If your light bulb will not light, check the bulb itself and light socket’s connection. If the socket is broken, or faulty it should be replaced immediately. Make sure to remove the high-voltage capacitor from your microwave before beginning this repair.

Tray,glass