LMX25988SB LG Refrigerator Parts List

Handle screw (stopper,handle)

This handle screw, also known as a mounting bolt, is a mounting screw to help secure the door handle to your refrigerator door. If your handle is loose, you may just need to tighten the screw. If your screw is missing or broken, it may need to be replaced. There are multiple handle screws on your fridge, please consider ordering extra as they commonly wear at the same rate. This is about 1 inch long and metallic in color.

Refrigerator door switch

The light switch lights up the interior cabinet of the refrigerator or freezer when the door is opened. If you open the door and the light won’t come on, or the light is always on, you may need to replace the light switch. The switch is white in color and measures approximately 2 1/2”. This is a genuine OEM part. Please remember to disconnect the power before starting the repair.

Refrigerator water filter (filter assembly,water)

This refrigerator water filter replacement is for 2010 LG refrigerators that have either forward French doors or are the four-door dispensing models. This filter is designed to minimize impurities that can cause ill-tasting water or an unpleasant smell. It reduces sediment, dirt, rust, limescale, sand, and many other contaminants that can be harmful to your health and the life of your appliance. This filter should be replaced every 6 months or 200 gallons to ensure top quality performance. To remove your unwanted filter, press the push button to open the filter cover (water may spill from the hole), pull out the old cartridge in a downward motion. To install the new filter, make it so the ears are in the horizontal position and push the new cartridge into the housing until it stops. Push the filter upward until it is secure. Click the cover to lock it in place. Run water for approximately 5 minutes to prep the filter for use, and discard water. Reset the “filter reset” button if applicable.

Plastic tube - 5/16 inch (tube,plastic)

The 5/16” plastic water tubing attaches to the water inlet valve and goes into the refrigerator. The tubing supplies water to the water dispenser and the ice maker. If the tubing becomes damaged or cracked, it can cause water to leak out onto the floor and the water tubing will need to be replaced. This is a genuine OEM part. Please remember to disconnect the power and water supply before starting the repair.

Water inlet valve assembly (valve assembly,water)

This includes the primary and secondary valves along with the wire harness.

Door holder (holder,door)

This is a manufacturer-approved refrigerator door closure for your refrigerator. It is made of white plastic and measures approximately 3 inches by 2 inches. If your old closure is damaged, your refrigerator door may not open and shut properly, and therefore it should be replaced.

Push button switch (switch,push button)

This is a genuine replacement switch. It is a push button style switch that is designed for use in your refrigerator. When the door of your appliance is opened the switch is released, and the light comes on. When you close the door the switch is pressed in, and the light turns off. You may need a putty knife to remove your old switch.

Evaporator fan motor (motor,dc)

This 13-volt evaporator fan motor helps circulate air over the refrigerator coils. These coils will then convert the heat into cool air, which is then circulated from the freezer section to the fresh food section. If the fresh food section is too warm or the motor has failed, you will need to replace the evaporator fan motor. It is suggested to replace the thermistor when replacing the evaporator fan. The fan motor is in the freezer section of the refrigerator, and includes the harness and plug. Please remember to disconnect the power to the refrigerator before starting your repair. This is a genuine OEM part.

Spring,lever

Door bin (basket assembly,door)

The door bin on your refrigerator is attached to the inside of the refrigerator door, and is designed to hold food and beverage items. It is made of white and clear plastic, and is approximately 14 inches wide. This is an authentic LG replacement part sourced directly from the manufacturer. Sold individually.

Refrigerator water reservoir (tank assembly,water)

The water reservoir holds the water for the water dispenser as the water chills.

Elbow (connector,tube)

Ice maker assembly kit (ice maker assembly,kit)

Screw,set

Compressor (lf)

This part must be installed by a licensed and trained LG technician that is able to perform a software update, which is required for the installation of this compressor. Part number CJT30000002 is needed to perform the update. Also, the three pins on the side of the new compressor may be oriented differently than the original. If different, when installing the new compressor the compressor electrical connector must be rotated 45 degrees counter-clockwise.