LRTD19A-AH59A Parts List

Evaporator fan motor - 115v 60hz - blade not included (evaporator fan motor for freezer..the evaporator fan motor draws air over the evaporator coils and circulates the cold air through the refrigerator an)

The evaporator fan motor circulates air over the refrigerator coils. These coils will convert the heat into cool air, which is then circulated. This part is 115 volts, has a 3/16th-inch shaft and is just over three inches long. It is made of both metal and plastic, and is made up of black, white, and metallic pieces. This evaporator fan motor is a genuine OEM part. Please remember to disconnect the power to your appliance before starting the repair.

Shelf trim end cap (door shelf retainer bar end cap, brown)

Sold individually.

Tray (ice cube making tray)

This fourteen cube ice cube tray is eleven inches long. It is all white in color and is made entirely of plastic.

Inlet hose washer (gasket, water inlet hose)

The high-pressure inlet hose washer is black in color. It is one inch in diameter, made of rubber, and used with many washing machines, refrigerators, and dishwashers. The washer helps by creating a watertight seal to avoid leaking. Over time the washer may be worn down or damaged and will need to be replaced. This is a genuine OEM part and is sold individually.

Cold control thermostat (temperature control thermostat assembly)

This cold control thermostat has a temperature range from 37 degrees Fahrenheit to 27 degrees Fahrenheit and a capillary length of 29 iches. This cold control thermostat cycles on and off regularly to keep your refrigerator cold.

Single hex head screw (screw 1/4" hex head, 10-12 x 1/2)

Sold individually. The size of this screw is 1/4" hex head and 10-12 x 1/2".

Ice stripper (ice stripper for icemaker)

This part strips ice from the icemaker mold during the ejection cycle to prevent ice pieces from falling back into the mold. Once removed from the mold, the ice pieces are then deposited into the ice bucket ready to be dispensed. If your ice maker is not making any ice you may need to replace this part. The part is white in color and is approximately 9-inch long. The ice stripper is a genuine OEM part. Please remember to disconnect power to your refrigerator before starting your repair.

Shelf trim end cap (bottom shelf end cap)

This door shelf trim end cap is brown in color and is made entirely of plastic.

Frame screw

Sold Individually.

Plastic tubing (1/4" plastic tubing, 8 1/2 feet long)

The water supply tubing is made of plastic and goes between the water inlet valve and the ice maker inlet tube. The tubing is 8 1/2 feet long and 1/4” in diameter. The water supply tubing transports water to the ice and water dispensers. If there is no water going to the ice maker, the refrigerator is leaking, or if the ice and water dispensers are not dispensing properly, you may need to replace the water supply tubing. This is an OEM part directly from the manufacturer. Please remember to shut off the water supply and to disconnect the power to your refrigerator before starting your repair.

Screw - 6-32 x 5/16 (screw, 6-32 x 5/16)

This screw is well under an inch long, and is made of metal.

Ice maker front cover (ice maker module front cover)

Shelf end cap - left or right side - beige (door shelf retainer end cap)

Sold individually.

Defrost heater (defrost heater for freezer evaporator, 21 inches)

This radiant glass defrost heater is twenty and a half inches long. It comes with an instructions sheet, and is intended for use with the freezer evaporator of some refrigerators.

Defrost evaporator pan (water collection and evaporation pan)

This defrost evaporator and water collection pan is almost sixteen inches long. It is all black in color and it is made entirely of plastic.