TD-V10010G Parts List

Parts assembly, svc (2 pack) (dryer drum roller. If the dryer is noisy the roller may be worn and requires replacement. The bearing in the roller is self-lubricating so no grease i)

The drum support roller for your dryer holds the drum in place while the drum turns on the support wheels. The drum roller is round with a bearing in the middle and measures approximately 3 inches in diameter. If the dryer is noisy, won’t tumble, or takes too long to dry, you might need to replace the support roller. It is recommended that you replace both rollers at once. The bearing inside this roller is self-lubricating, so no grease will be required. Please remember to disconnect the power to your appliance before starting your repair. This is a genuine OEM part.

Thermal fuse (dryer thermal fuse. If the dryer overheats, the thermal fuse blows to cut off power to the dryer. If the thermal fuse has blown, the dryer won't Star)

The high limit thermostat protects the dryer by shutting off the heating element when the dryer overheats. If the thermostat has blown, dryer won’t start or there is no heat, the thermostat will need to be replaced it can not be reset. If your dryer vent is clogged it could cause the thermostat to blow as well. This is a genuine OEM part. Please remember to disconnect the power to the dryer before starting the repair.

Dryer drum belt (dryer drum drive belt. 1/4 inch wide with 4 ribs and 3 grooves.)

The drive belt is made to wrap around the drum, working with the tension pulley to rotate the drum. If your dryer drum will not turn, then you may need to replace your belt. This drive belt is 1/4-inch wide with 4 ribs and 3 grooves. It is recommended to disconnect the power to your dryer before you start your repair. This drive belt is a genuine OEM part.

Moisture sensor (dryer moisture sensor bar. If the dryer timer does not advance properly inspect the moisture sensor bars for damage which can cause the automatic dryi)

The moisture sensor, also known as a humidity sensor, works in conjunction with your dryer by helping determine the amount of moisture in the drum to reduce overdrying. If the timer doesn’t advance correctly, it is suggested to check the moisture sensor bar for damage. A damaged sensor can cause the automatic drying cycle to not work properly and will need to be replaced. This is a genuine OEM part. Please remember to disconnect the power to the dryer before starting this repair.

High limit thermostat and thermistor kit (dryer thermistor assembly with wire harness. If the thermistor is defective, it can prolong or shorten the drying time or cause a fault code.)

The thermistor, with wire harness, helps regulate and monitor the temperature inside of the dryer. The thermistor attaches onto the blower housing. If your dryer has a short drying time or a fault code is flashing, the thermistor maybe defective and will need to be replaced. Please remember to disconnect the power to the dryer before starting the repair. This is a genuine OEM part.

Blower thermostat (thermostat)

The blower housing exhaust thermostat works in conjunction with your dryer by helping to regulate the temperature inside of the dryer drum. The thermostat will turn the heat off and on to help maintain the required temperature in the drum. If your dryer is not heating the thermostat may have shorted out and will need to be replaced. This is a genuine OEM part. Please remember to shut the power off to the dryer before starting the repair.

Cover,guide

Gas igniter (gas dryer igniter with bracket and wire harness. This is a round spiral-style igniter. The igniter uses heat to ignite the gas in the burner assembly.)

Comes with bracket and wire harness.

High limit thermostat (dryer high limit thermostat assembly. The thermostat has reset button in center it is trips due to poor air flow such as a clogged exhaust vent.)

This part is the replacement high-limit thermostat, or simply the thermostat for your dryer. It is approximately 2 inches wide from tip to tip. The center, rectangular portion of the thermostat is approximately 1 inch in width and a little more than 1 inch in length. The thermostat is a safety device that regulates the temperature inside the dryer. If the thermostat is shorted out, your dryer may not be getting any heat, and you will need to replace it. You can test the high limit thermostat for continuity by removing it and connecting it to a multimeter. Be sure to disconnect your dryer from the power source before you begin this repair. This is an OEM part sourced directly from the manufacturer.

Felt seal (felt seal, dryer drum)

Leg (dryer leveling leg)

This plastic adjustable dryer leg is used to support the weight and adjust the height of your dryer to keep it level. To install the leg, tip the dryer back and screw it into the bottom of your dryer unit. Please note that this dryer leg is sold individually.

Drive motor (dryer drum drive motor with pulley. If the dryer does not start the motor could be bad.)

This motor works with the belt to drive your dryer's drum.

Pulley,idle (idler pulley wheel with bearing)

Locker,hook (locker hook)

This is a door strike for your dryer. When you shut your dryer door, the door strike connects to the door catch and keeps the door closed. If the door strike is damaged, your door will not stay shut, and you will not be able to operate the dryer. It is made of metal and is approximately one inch long and half an inch wide. It is an authentic OEM part sourced directly from the manufacturer.

Switch assembly,safety