WCRD2050HW GE Washer Parts List

Tub dampening strap (washer tub dampening strap. If the washing machine tub is off-balance, then one or more of these straps may have broken.)

This part is used to support the tub and keep it in the center of the cabinet to reduce vibration. If your washer is making loud noises, or shakes or moves, one or more of the straps may have broken. It is recommended to replace all 4 tub dampening straps at the same time. This part is sold individually.

Dual action agitator (washing machine agitator assembly.)

This plastic dual action agitator is white in color. It is approximately eighteen inches tall with a base diameter of about 12-1/4 inches. The agitator pivots back and forth, moving the clothes from the top to the bottom of the tub, through the detergent and water to wash them. If the agitator becomes damaged or will not agitate, you may need to replace the part. This is a genuine OEM part. Please remember to shut off the water supply and disconnect the power to the washer before starting your repair.

Tub seal (washing machine main tub seal. If the washer leaks around the center shaft then the main tub seal is likely defective.)

The tub seal helps prevent any leaking around the transmission of your washer outer tub. If your washer is leaking you may need to replace the seal. The tub seal is located on the bottom of the outer tub, in the center where the transmission comes through to connect to the agitator. This is a genuine OEM part. It is suggested to have it installed by a qualified technician because the seal can be difficult to replace. Please remember to shut off the water supply and disconnect the power to the washer before starting your repair.

Drain pump and motor assembly (washing machine drain pump assembly. The drain pump pushes water through the drain hose during the drain cycle.)

This drain pump motor helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period. If your washer will not drain, is noisy, leaking, or pumps but will not spin, you may need to replace the drain pump motor. This is a genuine OEM part. Please remember to shut off the water supply and disconnect the power to the washer before starting your repair.

Agitator coupling (washing machine agitator drive bell (also called the coupler). The drive bell connects the transmission drive shaft to the agitator base.)

Bolt not included. This part connects the transmission drive shaft to the agitator base.

Shaft and mode shifter assembly (shaft and mode shifter assembly. The new mode shifter mounting holes are not threaded. You will need to use the original self tapping screws to instal)

Also known as the gearcase or transmission. This part helps move the agitator back and forth during the wash cycle. New shifter mounting holes are NOT threaded, use original self tapping screws to install new part. Tub seal is included with assembly.

Socket rod support - white (suspension rod support)

This part is a replacement socket rod support for your washer. The socket rod support is found at the top of the washer frame in the front part of the washer. It supports the suspension rod, so the rod can prevent the tub from shaking too much during operation. If your washer is shaking excessively or emitting an odd sound during use, it may be because the rod support is broken, and the suspension rod is not able to do its job. This part is made of white plastic and is sold individually.

Rod and spring assembly Green (suspension rod and spring assembly, Green)

This part helps center and support the drum, transmission and motor assembly.

Screw - 1/4-20 mch hxw 5/8 s (scr 1/4-20 mch hxw 5/8 s)

This is a replacement screw for your washer. The screw has a hex head and is approximately 1 inch in length. The washer portion of this screw is approximately 1 inch in diameter. This part is sold individually and is an authentic OEM part sourced directly from the manufacturer.

Screw - black (screw 8-18 ab ihwp 7/8 s)

This screw is sold individually.

Outer tub (washing machine outer tub. *for tub bearing see related items.)

This part holds the water during the wash cycle and houses the spin basket.

Tub cover - white (upper outer tub cover)

This cover goes on top of the balance ring that is located on top of the basket.

Locking clip

Sold individually.

Hinge bushing

Belt installation tool (service kit belt tool)

This part is the replacement belt install tool for your dryer. It comes with two round plastic halves of the tool that are held together with an o-ring (also included). To use the tool, position the two halves of the tool together, and roll the o-ring into the groove to secure. The belt install tool will allow you to replace a damaged drive belt on your dryer. Be sure to disconnect power to the dryer before you begin this repair. This is an OEM part sourced directly from the manufacturer.