WGD336RBW1 Frigidaire Dryer Parts List

Rear drum bearing kit (dryer rear drum bearing kit. The holes in the metal plate are not threaded. Use the self tapping screws in the kit to thread the plate.)

This rear drum bearing kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high temperature lubricant, and installation screws. The support bearing helps support the dryer drum to rotate quietly and smoothly during operation. The bearing attaches on the inside of the rear panel of the dryer cabinet. Over time the drum bearing will wear out. This kit will help keep your dryer running as smoothly as possible with as little noise as possible. This is a genuine OEM part. Please remember to disconnect the power before starting your repair.

Drum belt (dryer drum belt, length 87.75" x width 1/4". If the drum does not turn, but you can hear the motor running then there is a good chance the belt has br)

This dryer drum belt is 88 3/4 inches long, and is 1/4 inch wide. The belt attaches to the motor pulley and helps rotate the drum as the motor rotates. If the drum does not rotate and you can still hear the motor running, the belt may have broken and will need to be replaced. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Upper drum glide (front upper felt glide pad. Includes nylon glides, adhesive, and installation instructions. These drum glides help to support the front of the dryer d)

The upper drum felt glide kit helps to support the front drum as it rotates smoothly and quietly while operating. This kit includes three glides with the adhesive. If your dryer won’t tumble or is noisy, the glide could be worn down causing you to hear a metal on metal noise and will need to be replaced. The drum glide is a genuine OEM part and sold individually. Please remember to disconnect the power to the dryer before starting your repair.

M series ignition coil kit (dryer gas valve solenoid coil kit. The kit includes both 2 and 3 wire coils. If the dryer does not heat or heats intermittently the gas valve coils ma)

The gas dryer ignition coil set comes with two ignition coils: one three-terminal boost/hold coil, and one two-terminal secondary coil. If it takes too long to dry or there is no heat, the coils may be bad and will need to be replaced. When the coils go bad they will not hold the gas valve open properly. Usually only one of them burns out but you should replace them as a set. Both must be operational for the gas valve to open. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Lint screen and frame (lint filter screen and mounting frame)

This filter collects lint as it passes through the dryer vent.

Idler pulley assembly (idler tension pulley with bracket for dryer drum belt)

The idler pulley assembly provides the tension required for a flat belt. It also serves to help the belt to rotate the drum. This arm is what attaches to the idler pulley wheel. If your dryer is noisy or will not tumble you may need to replace the idler pulley. This is a genuine OEM part.

Door latch kit (dryer door catch kit. If the dryer does not latch properly then either the strike or catch is likely damaged and will need to be replaced.)

This door latch kit comes with the strike and the catch.

Flame sensor (flame sensor for gas dryer)

This part senses the flame for heat allowing the gas valve to open.

Timer knob (washer/dryer timer knob)

This knob accepts a D-shaped shaft.

Igniter (gas dryer igniter)

This part ignites the gas within the dryer. Be sure to not handle this igniter by the gray part as it is very fragile.

Front drum seal (front lower felt seal, drum)

Used with dryers with a 27-inch drum.

Levelling leg (dryer leveling leg. If your dryer is shaking during operation, this leveling leg may be damaged or unbalanced.)

Sold individually.

Handle-door white (door handle, white)

Push-to-start switch (dryer push to start switch)

This part is used to start the dryer once you have selected a setting with the timer.

Safety thermostat - l180-40f (dryer cycling thermostat, l100- 40f)