WM1811CW LG Washer Parts List

Washing machine drain pump (washer drain pump)

This drain pump motor helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period. If your washer will not drain, is noisy, leaking, or pumps but will not spin, you may need to replace the drain pump motor. This is a genuine OEM part. Please remember to shut off the water supply and disconnect the power to the washer before starting your repair. Note: Pump casing is not included.

Water inlet valve - hot (washer water inlet valve)

The hot water inlet valve is located on the back of the washer and it helps control the amount of water that enters into the washer. The valve has a standard hose fitting inlet, 1 water outlet, 120 volts and 6 watts. If the washer is filling slowly or not at all, the solenoid may have gone bad and you will need to replace the inlet valve. The valve measures approximately 3” L x 2 3/4” W. Please remember to disconnect the water and power to the washer before starting the repair. This is a genuine OEM hot water inlet valve.

Rear tub gasket (washer rear tub gasket)

The rear tub gasket is located between the drive shaft and the rear outer tub to form a watertight seal to prevent water from leaking. It is recommended to replace the two bearings at the same time as replacing the tub gasket. The gasket is black in color and measures approximately 3” in diameter. This is a genuine OEM part. Please make sure you disconnect the power and water supply to the washer before starting your repair.

Bearing,ball

The tub bearing supports the spin basket shaft at the back of the washing tub. If your washing machine will not spin, is leaking water, or if there is a loud screeching noise during the wash cycle, there could be an issue with the tub bearing. This genuine OEM replacement bearing has a 3-inch outer diameter, and is used to help the tub spin smoothly and to stop the washing machine from shaking during the cycle. NOTE: This part is very difficult to install. The manufacturer recommends replacing the complete rear tub and bearing assembly at the same time.

Gasket (washer outer tub gasket)

The outer tub gasket is used to create a seal between the front and rear outer tub to prevent water leaking. The tub gasket is located between the front outer tub and the rear outer tub. If your washer starts leaking from between the outer and rear tub, the tub gasket could be worn out or damaged and will need to be replaced. This part is black in color and made of rubber. This is a genuine OEM part. Please remember to disconnect the power and water supply to the washer before starting the repair.

Bearing,ball (tub bearing)

This is known as a tub bearing or a rear bearing, and it is part for your washing machine. The function of this bearing is to be a support for the spin basket shaft that is located at the back of the washer tub. This model is sold individually and measures to have a 2.5-inch outer diameter. As this bearing is very difficult to install, the manufacturer recommends completely replacing the rear tub and bearing assembly. If you are only installing the rear bearing, consider replacing the seal and the other bearing as they wear out together.

Door lock assembly (washer door lock switch)

Spider

This part is called a spider, spinner support or rear drum support for your washer. It is triangular, with three arms, and it is made of metal. The washer spinner supports and spins the tub while the washer is running. If you notice that your washer shakes or moves during operation, or if it is excessively noisy, you may need to replace the spider. This part is sold individually and is an authentic OEM part sourced directly from the manufacturer.

Sensor assembly (washer motor rotor position sensor)

The motor rotor position sensor monitors the direction and speed of the spinning rotor and communicates this information to the electronic control board. If your washer is displaying an LE error code on your control display, the sensor has failed and will need to be replaced. This is a genuine OEM part sourced directly from the manufacturer. Please remember to disconnect the power to your washer before starting your repair.

Tub-to-pump drain hose (washer tub-to-pump hose)

This hose has bellows to allow for flexibility during the wash and spin cycles.

Leg assembly

This levelling leg is a genuine replacement part. It is used to help keep your washing machine stable and balanced. It helps support your appliance. It screws into the base of your washer, and you can thread it in or out to adjust the height. The foot on this leg is made of rubber, which helps with grip, stabilization, and vibration reduction. It is also hexagonal in shape, which allows you to more easily adjust it. This levelling leg features a locknut on the shaft which can be tightened against the bottom of your appliance, this will stop the leg from rotating while you are using your washer. This replacement is sold individually.

Washing machine bolt

Shock absorber assembly (washer damper)

Sold individually

Clamp assembly (washer door boot spring clamp)

The door boot seal clamp, also referred to as an outer door gasket clamp, holds the door boot in place in a front-loading washer. If your washer is leaking from the door and there are no signs of damage to the door boot seal, check to ensure that it is securely fastened. If your boot seal clamp is faulty, or damaged, it should be replaced immediately.

Pump filter (washer drain pump clean-out filter)

This replacement pump filter, also known as a filter assembly, is a genuine OEM part for your washer or washer/dryer combo. Before beginning this repair, turn off the power and water supply to your washer. The filter assembly may need to be replaced because it is broken or is leaking water. To locate the filter assembly, pry open the small door on the front of the washer, using a flat-blade screwdriver. Unplug the drain hose next to the filter and drain the water into a bucket. Then unscrew the pump filter, and replace with your new one.