YOUR ORDER SHIPS THE SAME DAYOn in-stock orders placedbefore 4pm Eastern Time.
Search by part or model number
Every model has its own, specific solutions. If you go to a car mechanic they'll need to know the exact make and model of your car to find the right repair parts. Appliances are the same.
See this guide for help.
Don't let a broken Kenmore Refrigerator ruin your day. Repair your Refrigerator with parts from EasyApplianceParts.com. We offer low prices, award winning service and same day shipping on all Kenmore Refrigerator parts to help you repair any of your home appliances.
Easy Part #:
In Stock - Ships Today
This metallic screw is less than an inch long and comes with a plastic washer.
The humidity control allows you to adjust the humidity within the crisper. This can extend the life of the vegetables/fruit.
***NOTE: Ice maker does NOT come with the bail or shut off arms. Must order them separately if required. It does come complete with flat and round plug wiring harness, the mounting hardware, and the instructions. Its harness can be reused. The ice maker will not fit refrigerators that have the ice auger mounted on the door.
This eight-hour defrost timer will replace most other defrost timers. This device acts like a clock. It continually advances and alternates between activating the cooling cycle and the defrost heater. The best way to make sure you get the correct timer for your refrigerator is to conduct a search for your model number.
This part is used to help tell the icemaker what to do - it turns the timing cams and the ejector blades. Motor is not sold separately.
As you look into the fridge, this drawer support track is located on the right hand side.
Sold individually. The size of this screw is 1/4" hex head and 10-12 x 1/2".
This door closing cam is located on the bottom of the fridge/freezer.
This part can be used for the front support. Sold individually and mounts to the inside cabinet wall.
Also called Vegetable Drawer. Sold individually.
This kit includes the ice door, support, spring and delay. The heater ribbon is no longer attached - the heater is no longer needed.
This condenser fan motor operates in a clockwise fashion and carries carries 2W and 115V. It comes with screws, a blade mounting nut, and a cushion. This part provides forced-air cooling for the condenser coil.
This bin is clear with a white trim around the top edge. Sold individually.
Note: As per manufacture a new screw is needed to mount door cam.
This defrost timer will cycle for thirty minutes after every eight hours of run time.
This screw is sold individually.
The bulb is sold separately.
This door bin holds items on the door of your refrigerator. They are sometimes called Cantilever Shelves as they are supported by the back of the shelf itself to the door of your refrigerator.
This filter is used on side-by-side refrigerators with the push button in the front bottom grill. It reduces cysts, chlorine, taste, odor, lead and micro particles. Sold individually.
This part helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer.
This is a 12 piece kit.
Replacement icemaker kit - electronic. This kit includes a 4 pin round plug-in connector, 6 post plug-in connector, tube and fill cup.
This part is also known as Cover.
This kit includes the motor, clips and terminal connectors. This part has been updated by the manufacture.
This evaporator fan motor is located in the back of the freezer, and circulates air over the refrigerator coils. These coils will convert the heat into cool air, which is then circulated.
This white bin can also be used on the freezer door on some models. Sold individually.
This fresh food door gasket is used to seal the refrigerator door when closed to keep the cool air inside and the room air outside.
NOTE: This part is actually white and black.
This retainer bar is cut to fit.
This part is the replacement heat-release ice maker unit only. This kit comes with four round female connectors at the end of the wire harness. It also comes with the adaptor that converts the harness to three round female and one round male connectors.
This drawer rail supports the left hand side of the sliding drawer. The mounting screws are sold separately.