YOUR ORDER SHIPS THE SAME DAYOn in-stock orders placedbefore 4pm Eastern Time.
Search by part or model number
Every model has its own, specific solutions. If you go to a car mechanic they'll need to know the exact make and model of your car to find the right repair parts. Appliances are the same.
See this guide for help.
Don't let a broken Kenmore appliance ruin your day. Repair your appliance with parts from EasyApplianceParts.com. We offer low prices, award winning service and same day shipping on all Kenmore appliance parts to help you repair any of your home appliances.
Easy Part #:
In Stock - Ships Today
This dryer drum belt has four ridges, three grooves and is 1/4" wide.
This dryer door latch kit comes with one plastic door latch and one metal door strike.
This part is a one-time use thermal fuse which attaches to the blower wheel housing of your clothes dryer. It cannot be re-set and must be replaced when continuity between the pins is no longer present. Terminal size is 3/16".
The humidity control allows you to adjust the humidity within the crisper. This can extend the life of the vegetables/fruit.
This gas dryer ignition coil set comes with two ignition coils: one three terminal Boost/Hold coil, and one two terminal secondary coil. Usually only one of them burns out but you should replace them as a set. Both have to be operational for the gas valve to open.
These agitator directional cogs are commonly referred to as dog ears. They come four to a package and are usually used with direct drive washing machines.
It is intended for use with washing machines that do not have belts. This drain pump has two ports for water to pass through: a large one, and a smaller one.
This motor fits most Whirlpool incorporated dryer brands before 1996. NOTE: Pulley is NOT available separately.
This door closing cam is located on the bottom of the fridge/freezer.
This coupling kit is used between the motor and the transmission on direct drive washers with no belt. This is the newer version and is made with new metal sleeves for added strength.
This six inch chrome drip bowl is intended for use with rolled terminal style plug in surface element units.
Also called Vegetable Drawer. Sold individually.
This hose clamp is sold individually.
This part provides the tension required for a multi-ribbed belt. It also serves to help the belt to rotate the drum. This arm is what attaches to the idler pulley wheel.
These two drum support rollers are no longer available for individual sale. Available in a package of two and it is recommended that you replace both rollers at once. These two rollers come with four tri-rings and one palnut.
This screw is sold individually.
Also known as Main Outer Tub Seal. This part helps to prevent leaking from the bottom of the tub.
***NOTE: Ice maker does NOT come with the bail or shut off arms. Must order them separately if required. It does come complete with flat and round plug wiring harness, the mounting hardware, and the instructions. Its harness can be reused. The ice maker will not fit refrigerators that have the ice auger mounted on the door.
This silicone carbide igniter with ceramic holder kit includes the 3" flat igniter, bracket, 5" wire leads, and the plug. Able to replace both round and flat igniters, this kit is used for many gas clothes dryers.
This metallic screw is less than an inch long and comes with a plastic washer.
This bin is clear with a white trim around the top edge. Sold individually.
A worn clutch can cause a slower spin speed which will leave your clothes wet after a cycle.
This clutch assembly comes with brake cam driver, blue spring for large capacity washers and black spring for compact washers. As per factory, the green spring (1.24") replaces the black spring (1.46").
This kit includes the ice door, support, spring and delay. The heater ribbon is no longer attached - the heater is no longer needed.
This gray and white washer lid bumper contains a rubber bottom and is sold individually.
As you look into the fridge, this drawer support track is located on the right hand side.
This part can be used for the front support. Sold individually and mounts to the inside cabinet wall.
This part can be used for the rear support, and mounts to the inside cabinet wall. Sold individually.
This defrost timer will cycle for thirty minutes after every eight hours of run time.
This filter is used on side-by-side refrigerators with the push button in the front bottom grill. It reduces cysts, chlorine, taste, odor, lead and micro particles. Sold individually.
This door bin holds items on the door of your refrigerator. They are sometimes called Cantilever Shelves as they are supported by the back of the shelf itself to the door of your refrigerator.
This part is used to help tell the icemaker what to do - it turns the timing cams and the ejector blades. Motor is not sold separately.
This kit contains one wheel and one axle. It is designed for the rear lower dishrack.
Sold individually. Order quantity needed.
Note: As per manufacture a new screw is needed to mount door cam.
This fresh food door gasket is used to seal the refrigerator door when closed to keep the cool air inside and the room air outside.
NOTE: This part is actually white and black.
Sold Individually. Appliance takes 3 of this part.
NOTE: This replacement ice maker mechanism does NOT come with a cover,shut off arm, a wire harness, or the mounting hardware. Must be ordered separately.