Parts for Kenmore Models 40311

Lower rack wheel kit - 8 pack (srv-stud roller asm kit)

The lower rack wheel kit includes 8 wheels and 8 axels for your rack. If your dishrack is not moving in and out of the dishwasher properly you may have a broken or missing wheel and it will need to be replaced. The wheel and axle are white in color and made of plastic. This is a genuine OEM part kit.

Easy Part #:: EAP11726733

Availability:: In Stock

Price:: $29.43

Single lower wheel stud/axle (srv- stud roller asm kit)

The rack roller axle attaches the roller to the lower rack to allow you to move the dishrack in and out with ease. The axles sometimes wear out at the same rate and the manufacturer recommends replacing them in pairs. This part is light gray in color, made of plastic and measures 1” x 1” x 1/2” deep. The wheel is not included, just the axle. This is a genuine OEM part and is sold individually.

Easy Part #:: EAP2353872

Availability:: In Stock

Price:: $7.34

Rack slide end cap

This white rack track stop is used for your upper dishrack track to prevent the rack from sliding off the slide rail. If your rack is falling off the track, you may need to replace the track stop. This is a genuine OEM part and is sold individually.

Easy Part #:: EAP2370502

Availability:: In Stock

Price:: $11.76

Washing machine drain pump

This drain pump motor helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period. If your washer will not drain, is noisy, leaking, or pumps but will not spin, you may need to replace the drain pump motor. This is a genuine OEM part. Please remember to shut off the water supply and disconnect the power to the washer before starting your repair. Note: Pump casing is not included.

Easy Part #:: EAP3579318

Availability:: In Stock

Price:: $65.83

Dishwasher dishrack rollers and axles (dishwasher upper rack kit 4-pack)

This is a kit of 4 and also includes 4 axles.

Easy Part #:: EAP11721505

Availability:: On Order

Price:: $32.37

Basket asm silverware (basket silverware end)

This basket is part of a silverware basket that has 3 sections. This is the middle section of the basket.

Easy Part #:: EAP12703061

Availability:: In Stock

Price:: $30.40

Water inlet valve - hot

The hot water inlet valve is located on the back of the washer and it helps control the amount of water that enters into the washer. The valve has a standard hose fitting inlet, 1 water outlet, 120 volts and 6 watts. If the washer is filling slowly or not at all, the solenoid may have gone bad and you will need to replace the inlet valve. The valve measures approximately 3” L x 2 3/4” W. Please remember to disconnect the water and power to the washer before starting the repair. This is a genuine OEM hot water inlet valve.

Easy Part #:: EAP3527427

Availability:: In Stock

Price:: $23.09

Detergent dispenser with rinse cap (module rinse and cap asm)

This part releases the detergent and rinse aid into the dishwasher.

Easy Part #:: EAP958966

Availability:: In Stock

Price:: $78.13

Rear tub gasket

The rear tub gasket is located between the drive shaft and the rear outer tub to form a watertight seal to prevent water from leaking. It is recommended to replace the two bearings at the same time as replacing the tub gasket. The gasket is black in color and measures approximately 3” in diameter. This is a genuine OEM part. Please make sure you disconnect the power and water supply to the washer before starting your repair.

Easy Part #:: EAP3522855

Availability:: In Stock

Price:: $26.33

Recess door spring (spring recess door)

This door recess spring or dispenser lever spring in your refrigerator is used to return the ice door to the closed position or the dispenser lever to the home position once released. You will find the spring in the water dispenser assembly, behind the main control panel. If the dispenser lever is malfunctioning or the dispenser ice door is not closing, you may need to replace this door recess spring.

Easy Part #:: EAP285013

Availability:: In Stock

Price:: $11.16

Water inlet valve (water valve)

This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed. This valve has a 3/8" inlet and comes with the mounting bracket.

Easy Part #:: EAP259368

Availability:: In Stock

Price:: $76.60

Water inlet valve - cold

This valve is used for cold water, bleach dispenser, and prewash cycles. It has a standard hose fitting inlet with 2 outlets facing 45 degrees to the right and one outlet facing 45 degrees to the left. The water inlet valve opens to allow the water to enter the washing machine. If your washer will not fill with water, is leaking, or will not stop filling with water, you may need to replace the valve. Please remember to disconnect the power to your washer, remove the fill hoses on the back and pull out the washer to have access to the back before you start your repair. This valve is a genuine OEM part.

Easy Part #:: EAP11728995

Availability:: In Stock

Price:: $58.85

Bearing,ball

The tub bearing supports the spin basket shaft at the back of the washing tub. If your washing machine will not spin, is leaking water, or if there is a loud screeching noise during the wash cycle, there could be an issue with the tub bearing. This genuine OEM replacement bearing has a 3-inch outer diameter, and is used to help the tub spin smoothly and to stop the washing machine from shaking during the cycle. NOTE: This part is very difficult to install. The manufacturer recommends replacing the complete rear tub and bearing assembly at the same time.

Easy Part #:: EAP7785069

Availability:: In Stock

Price:: $47.92

Upper track roller kit (roller & stud)

This upper track roller kit comes with a screw for easy assembly.

Easy Part #:: EAP259157

Availability:: In Stock

Price:: $11.50

Gasket

The outer tub gasket is used to create a seal between the front and rear outer tub to prevent water leaking. The tub gasket is located between the front outer tub and the rear outer tub. If your washer starts leaking from between the outer and rear tub, the tub gasket could be worn out or damaged and will need to be replaced. This part is black in color and made of rubber. This is a genuine OEM part. Please remember to disconnect the power and water supply to the washer before starting the repair.