40311 Parts List

Scr b-16 hxw 1/2 stainless steel (bearing mid spray arm)

This part is a replacement middle spray arm bearing for your dishwasher. The spray arm bearing reduces friction and allows the spray arm to rotate during the operating cycle. If the spray arm is not rotating or cleaning dishes properly, or is noisy during operation, you may need to replace the spray arm bearing. This is a bearing for the middle spray arm, which is mounted to the bottom of the upper dish rack. The bearing is made of metal and is approximately one inch in diameter. This part is sold individually and is an OEM part.

Hose assembly,drain

Check valve flapper (valve flapper)

This part allows the water to flow in the drain direction only and prevents the dirty water from coming back into the tub.

Pump filter

This replacement pump filter, also known as a filter assembly, is a genuine OEM part for your washer or washer/dryer combo. Before beginning this repair, turn off the power and water supply to your washer. The filter assembly may need to be replaced because it is broken or is leaking water. To locate the filter assembly, pry open the small door on the front of the washer, using a flat-blade screwdriver. Unplug the drain hose next to the filter and drain the water into a bucket. Then unscrew the pump filter, and replace with your new one.

Inlet sump (inlet)

This works in conjunction with the pump and filtration system. It is used to receive drainage for disposal.

Middle spray arm kit (no longer available)

This kit includes the middle spray arm, hub with hub nut and washer. Screw is NOT included.

Cap,drain hose (drain hose cap)

This drain hose plug, also known as a hose cap, is a genuine OEM part for your washing machine. This plug caps the drain hose from the pump housing, and helps prevent leaks from your washer. Before beginning this repair, make sure the power and water sources to your washer are shut off. To access the pump housing, open the pump filter cover, pull out the drain hose, remove the old plug and replace it, first draining the remaining water from the drain hose.

Bolt assembly

Lower spray arm bearing (bearing spray arm low - spacer)

This part is a replacement lower spray arm bearing for your dishwasher. It is made of gray plastic and is approximately ½ inch in diameter. The spray arm bearing reduces friction and allows the spray arm to rotate during the operating cycle. If the spray arm is not rotating or cleaning dishes properly, or the dishwasher is noisy during operation, you may need to replace the spray arm bearing. This is a bearing for the middle spray arm, which is mounted to the bottom of the upper dish rack. The bearing is made of metal and is approximately one inch in diameter. This part is sold individually and is an OEM part.

Hinge assembly

The door hinge attaches the door to the front panel of the washer cabinet. If the door hinge is damaged, or faulty, the door may not close or open properly and can lead to the unit leaking during the wash cycle. This genuine OEM part is sourced directly from the manufacturer, made of stainless steel, and measures approximately 12 inches long x 6 inches wide.

Pump casing

This part connects to the drain pump and motor.

Bolt assembly

Clamp

The hose clamp works in conjunction with the water hose in the appliance by holding the water hose in place to keep the hose from leaking water on to the floor. If you notice your appliance leaking, you may have a crack in the hose or that the clamp is loose and will need to be replaced. The hose clamp is made of metal, measures approximately 1/2” in diameter and sold individually. This is a genuine OEM part.

Drain hose

This drain hose is an OEM, manufacturer-approved replacement part for your dishwasher. The drain hose filters out the wastewater from the dishwasher. If there is a hole in it, water will leak out of your dishwasher. Shut off the water and power to the unit before beginning this repair. Accessing the drain hose involves unscrewing the dishwasher and pulling it out. Remove the clamp holding the hose in place to its connection under the sink, using a 5/16ths socket. Disconnect the fill line. Use a 1/4 inch nut driver to loosen the clamp at the other end of the drain hose. Keep a towel handy for any water still inside. Keep the clamps for use on your new drain hose. Reinstall all hoses and lines in reverse order.

Main conduit (conduit main)

Also known as Upper Wash Supply Tube. This part brings water from your main water line the wash arms.