41729 Parts List

Sensor assembly (washing machine rotor position sensor assembly. This part is also called a hall sensor or motor sensor. When this part fails the control may display a)

The motor rotor position sensor monitors the direction and speed of the spinning rotor and communicates this information to the electronic control board. If your washer is displaying an LE error code on your control display, the sensor has failed and will need to be replaced. This is a genuine OEM part sourced directly from the manufacturer. Please remember to disconnect the power to your washer before starting your repair.

Remote style pump with motor (drain pump assembly)

Use this with either a top load or front load washer. This pump has an horizontal mount.

Tub-to-pump drain hose

This hose has bellows to allow for flexibility during the wash and spin cycles.

Screw (drum vane screw)

This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. The main reason you would replace this screw is if the old screw is missing or damaged. This part is sold individually and is an OEM part sourced directly from the manufacturer.

Shock absorber kit (shock absorber with two mounting pins)

This kit includes 1 shock absorber and 2 mounting pins.

Drain hose

This part comes with a ninety degree elbow.

Screw (pan-head screw)

Sold individually.

Washer hose with bellows (bellows)

This washer hose with bellows, also known as a dispenser hose, is a genuine OEM replacement part for your washer. Replacing this part can be helpful if your washer is leaking. The dispenser hose connects the dispenser assembly to the tub. Before beginning the repair, unplug the washer and turn off the water supply. You will need a Phillips head screwdriver to complete this repair; a clamp tool can also be helpful. Remove the screws holding the lid of the washer in place, and take off the lid. Locate the dispenser hose and remove its clamps. Place the clamps on the new hose, using the arrows for a guide in positioning the clamps. Install the new hose and reassemble all other parts.

Drive belt - 6 ribs (belt)

This is a drive belt for your washing machine. This part spins the basket in your appliance by connecting the drive motor to the drive system. You will need to replace the drive belt if your pumps are not spinning, your washer is not agitating, or you are noticing excess noise and/or a burning smell. This belt is black with six ribbings. To replace this part, you will need a Phillips screwdriver.

Motor assembly,ac,pump (circulation or drain pump assembly. This pump is found on both washing machines and dishwashers. On washing machines, this pump is used to circulate t)

The circulation pump is used in both washers and dishwashers. In the washer, the pump is used to circulate the water during operation. In the dishwasher, the pump is used to drain the water from the dishwasher. If the circulation pump stops working, it will prevent the washer and dishwasher from working properly and will need to be replaced. This circulation pump is 120 volts, 60Hz and 30 watt and a genuine OEM part. Please remember to disconnect the power and water supply before starting your repair.

Leg assembly

This levelling leg is a genuine replacement part. It is used to help keep your washing machine stable and balanced. It helps support your appliance. It screws into the base of your washer, and you can thread it in or out to adjust the height. The foot on this leg is made of rubber, which helps with grip, stabilization, and vibration reduction. It is also hexagonal in shape, which allows you to more easily adjust it. This levelling leg features a locknut on the shaft which can be tightened against the bottom of your appliance, this will stop the leg from rotating while you are using your washer. This replacement is sold individually.

Drum vane

Also known as a Drum Baffle. Sold individually.

Locking pin (shock absorber locking pin)

The locking pin is used to hold the shock absorber on the washer. There is a pin used at the bottom and top of the shock absorber. Sold individually.

Spring,hinge (suspension spring)

Washer tub bearing (tub bearing. This parts is very difficult to install. The manufacturer recommends replacing the complete rear tub and bearing assembly.)

Tub bearing. This part is very difficult to install. The manufacturer recommends replacing the complete rear tub and bearing assembly.