F12A1FD LG Washer Parts List

Washing machine drain pump (washing machine drain pump. If the washer does not drain then the drain pump may be clogged, damaged, or defective.)

This drain pump motor helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period. If your washer will not drain, is noisy, leaking, or pumps but will not spin, you may need to replace the drain pump motor. This is a genuine OEM part. Please remember to shut off the water supply and disconnect the power to the washer before starting your repair. Note: Pump casing is not included.

Water inlet valve - hot (valve assembly,inlet)

The hot water inlet valve is located on the back of the washer and it helps control the amount of water that enters into the washer. The valve has a standard hose fitting inlet, 1 water outlet, 120 volts and 6 watts. If the washer is filling slowly or not at all, the solenoid may have gone bad and you will need to replace the inlet valve. The valve measures approximately 3” L x 2 3/4” W. Please remember to disconnect the water and power to the washer before starting the repair. This is a genuine OEM hot water inlet valve.

Rear tub gasket (gasket)

The rear tub gasket is located between the drive shaft and the rear outer tub to form a watertight seal to prevent water from leaking. It is recommended to replace the two bearings at the same time as replacing the tub gasket. The gasket is black in color and measures approximately 3” in diameter. This is a genuine OEM part. Please make sure you disconnect the power and water supply to the washer before starting your repair.

Magnetic door plunger (washer door magnet holder kit)

The magnetic door plunger attaches to the inner door panel of your washer and will hold the door open when the washer is not in use and allows the door and tub seal to dry. By doing this it will prevent mold and mildew buildup around your door and seal. If your washer door will not close you many need to replace this part. The magnetic door plunger is a genuine OEM part.

Bearing,ball

The tub bearing supports the spin basket shaft at the back of the washing tub. If your washing machine will not spin, is leaking water, or if there is a loud screeching noise during the wash cycle, there could be an issue with the tub bearing. This genuine OEM replacement bearing has a 3-inch outer diameter, and is used to help the tub spin smoothly and to stop the washing machine from shaking during the cycle. NOTE: This part is very difficult to install. The manufacturer recommends replacing the complete rear tub and bearing assembly at the same time.

Gasket (washing machine tub seal. Located between the front outer tub and rear outer tub.)

The outer tub gasket is used to create a seal between the front and rear outer tub to prevent water leaking. The tub gasket is located between the front outer tub and the rear outer tub. If your washer starts leaking from between the outer and rear tub, the tub gasket could be worn out or damaged and will need to be replaced. This part is black in color and made of rubber. This is a genuine OEM part. Please remember to disconnect the power and water supply to the washer before starting the repair.

Door gasket (gasket)

Also known as a door boot seal or bellow and comes with a drain hole. Door boot 4986ER0004F is an original equipment manufacturer (OEM) part that fits some front-load washers in these series: Kenmore and Kenmore Elite 796; and LG WM and CW. Door boot 4986ER0004F forms a seal between the wash tub and the door, preventing leaks. This door boot includes a drain port; if your 27-inch LG front-load washer was made before September 2007, use door boot 4986ER0004B instead, because those washers don't have a drain port.

Bearing,ball

This is known as a tub bearing or a rear bearing, and it is part for your washing machine. The function of this bearing is to be a support for the spin basket shaft that is located at the back of the washer tub. This model is sold individually and measures to have a 2.5-inch outer diameter. As this bearing is very difficult to install, the manufacturer recommends completely replacing the rear tub and bearing assembly. If you are only installing the rear bearing, consider replacing the seal and the other bearing as they wear out together.

Shock absorber kit

This kit includes 1 shock absorber and 2 pins.

Spider

This part is called a spider, spinner support or rear drum support for your washer. It is triangular, with three arms, and it is made of metal. The washer spinner supports and spins the tub while the washer is running. If you notice that your washer shakes or moves during operation, or if it is excessively noisy, you may need to replace the spider. This part is sold individually and is an authentic OEM part sourced directly from the manufacturer.

Door lock assembly (switch assembly,locker)

Detergent dispenser (box assembly,detergent)

The blue plastic detergent dispenser holds the detergent and then dispenses it into the washer during the wash cycle. If the detergent dispenser is broken, lost, or if the detergent is not dispensed during the wash cycle, you may need to replace it. The dispenser is approximately 4-inches wide, 4.5-inches long, 2-inches tall and is a genuine OEM part.

Tub-to-pump drain hose (bellows)

This hose has bellows to allow for flexibility during the wash and spin cycles.

Inlet valve assembly (valve assembly,inlet)

This valve is used for cold water, bleach dispenser and prewash cycles. It has a standard hose fitting inlet with 2 outlets facing 45 degrees to the right and one outlet facing 45 degrees to the left.

Washer hose with bellows (bellows)

This washer hose with bellows, also known as a dispenser hose, is a genuine OEM replacement part for your washer. Replacing this part can be helpful if your washer is leaking. The dispenser hose connects the dispenser assembly to the tub. Before beginning the repair, unplug the washer and turn off the water supply. You will need a Phillips head screwdriver to complete this repair; a clamp tool can also be helpful. Remove the screws holding the lid of the washer in place, and take off the lid. Locate the dispenser hose and remove its clamps. Place the clamps on the new hose, using the arrows for a guide in positioning the clamps. Install the new hose and reassemble all other parts.