Parts for Kenmore Models LA710S

Belt kit (washer belt kit for Maytag models. If the washer does not agitate, spin, or drain then one of the belts could be worn and require replacement.)

There are two belts under a Maytag washer; one for the main drive pulley and one for the water pump. The belt kit includes both the drive belt and the pump belt which are both V-shaped. The belt connects the drive motor to the drive system to be able to spin the tub basket. If your washer will not agitate, not spin, or not drain, the belt could be worn or damaged and will need to be replaced. This is a genuine OEM kit. Please remember to disconnect the power and shut off the water supply to your washer before starting your repair.

Easy Part #:: EAP2005284

Availability:: In Stock

Price:: $37.07

Lid switch (dryer door/washer lid switch kit)

The door switch is a simple on/off mechanism that prohibits the dryer from operating when the door is open. The dryer cannot operate until the door switch signals that the door is closed. If your dryer will not start or the switch shorted out, your washer will not operate and the switch will need to be replaced. This switch is a genuine OEM part. Please remember to disconnect power to the dryer before starting the repair.

Easy Part #:: EAP11723153

Availability:: In Stock

Price:: $22.04

Water inlet valve (washing machine water inlet valve top-loading unit, valve has multi-mount bracket & outlet adaptor)

This water inlet valve has two ports for water to enter. It is blue and is intended for use with many washing machines and comes with a multi-mount bracket and an outlet adaptor. The water inlet valve controls the water flow into your washer. If your washer is leaking, will not fill with water, has no hot/cold water, or will not stop filling with water, you may need to replace the valve. This is a genuine OEM part. Please remember to shut off the water supply and disconnect the power to the washer before you start the repair.

Easy Part #:: EAP1583805

Availability:: In Stock

Price:: $76.79

Mounting stem/tub seal kit (washing machine tub seal repair kit. This kit is for Maytag two belt washers. If the washing machine is leaking water from above the transmission this)

This tub seal helps prevent any leaking around the tub and the shaft of your washer. If your washer is leaking you may need to replace the seal. The tub seal is located on the bottom of the outer tub, in the center where the transmission comes through to connect to the agitator. This is a genuine OEM part. Please remember to shut off the water supply and disconnect the power to the washer before starting your repair.

Easy Part #:: EAP2351899

Availability:: No Longer Available

Rubber injector valve (injector tube for water inlet system on Maytag 2 belt washers)

This rubber injector valve is commonly known to cause a leak at the top left corner of the outer tub. It fits over the injector nozzle. This part helps control the water flow rate from the fill valve to the tub. If your washer is leaking you may need to replace this part. This injector valve is a genuine OEM part. Please remember to disconnect power to your washer before starting your repair.

Easy Part #:: EAP11738945

Availability:: In Stock

Price:: $19.84

Screw, 8/18 x 3/8 (screw, 10-24 3/8)

This screw is sold individually.

Easy Part #:: EAP11746840

Availability:: In Stock

Price:: $7.40

Drain pump (Maytag two belt washing machine drain pump. If the washer does not drain then the pump could be clogged or defective.)

This washing machine drain pump is intended for use with automatic washers that have been manufactured since 1958. The pump itself is made of plastic, though it does come with a metallic belt pulley.

Easy Part #:: EAP11743017

Availability:: In Stock

Price:: $104.30

Hose clamp

This hose clamp expands from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag washing machines to secure the end of the drain hose to the pump drain port. Please make sure to disconnect the power to your washer before you start your repair. This hose clamp is a genuine OEM part and is sold individually.

Easy Part #:: EAP11743008

Availability:: In Stock

Price:: $6.64

Tub bearing kit (washing machine tub bearing repair kit. The tub bearing is mounted in the middle of the outer tub of the washing machine. The tub bearing helps to kee)

The tub bearing kit is used on 2-belt washers. This part helps keep the interior tub spinning correctly. If your washer is leaking, noisy, or shakes and moves, you may need to replace the tub bearing. It is recommended to change the seal kit at the same time you are replacing the tub bearing. This is a genuine OEM part. Remember to disconnect the power and shut off the water supply to the washer before starting your repair.

Easy Part #:: EAP2347235

Availability:: In Stock

Price:: $45.80

Washing machine lid hinge ball (lid hinge ball)

This washing machine lid hinge ball is well under an inch in diameter. These hinge balls are sold separately, though two are required per lid. This lid hinge ball is made of plastic and is used for Maytag brand washing machines.

Easy Part #:: EAP11738871

Availability:: In Stock

Price:: $10.37

Plastic injector nozzle (nozzle for water injector tube)

This injector nozzle is just under three inches long. It is white in color and made entirely of plastic.

Easy Part #:: EAP11738878

Availability:: In Stock

Price:: $9.63

Adjustable leveling leg (adjustable leveling leg with stop-nut)

The adjustable leveling leg is used to support and keep your washer level. If your washer shakes and moves during cycles you may need to replace the leveling leg. The stop nut is included with the leveling leg. The rubber foot is not included, it must be ordered separately. Order the quantity you need as they are sold individually. This is a genuine OEM part.

Easy Part #:: EAP2021026

Availability:: In Stock

Price:: $17.19

Washer lid bumper (lid bumper)

This washing machine lid bumper is just under an inch long. It is all gray in color and is made entirely of rubber.

Easy Part #:: EAP11738875

Availability:: In Stock

Price:: $7.17

Spring retaining clip (front cover top retaining spring clip)

This spring retaining clip is used to hold the front panel onto the top of the washer. If your front panel is loose you might need to replace the clip. The clip is made entirely of metal and is used for some washing machines. This part is not quite an inch long and is sold individually. This is a genuine OEM part.

Easy Part #:: EAP11739294

Availability:: In Stock

Price:: $10.33

Outer tub to pump hose (tub to pump drain hose)

This hose connects the outer tub to the pump of your washing machine. It is twelve inches long and all black in color. This hose is made entirely of rubber.