PCF25MGWC GE Refrigerator Parts List

Light switch (switch light)

This is the light switch that goes in your refrigerator. If the light is not working or stays on, you may need to replace the switch. It is made of mainly white plastic, and is an OEM part, directly from the manufacturer. Be sure to disconnect the refrigerator from the power source before you begin this repair. To remove the switch, simply use a flathead screwdriver to pop the switch out from the refrigerator wall, then disconnect the wires. Reconnect the wires to the new switch, snap it into place, and the repair is complete.

Snack pan (pan asm top)

Sold individually.

Dispenser door recess crank (crank door recess)

The door recess crank for your refrigerator is located inside the water dispenser assembly. To access this part, you will need to take apart the dispenser assembly. To do this, you will need a putty knife and a Phillips screwdriver. If your dispenser door will not close properly, or ice is not dispensing properly, you may have a damaged door recess crank. This part is made of white plastic and is sold individually.

Shelf stop - white (stop shelf)

The shelf stop in your refrigerator is what locks the shelf into the refrigerator liner. The shelf stop can be found attached to the shelf. To remove the shelf stop, begin pulling the shelf out until the stop hits the refrigerator liner, then depress the shelf stop to remove the shelf. With the shelf removed, you can simply slide the old stop out of its groove, and replace it with a new one. This part is made of white plastic and is about 1 inch in length. It is sold individually, and is an OEM part sourced directly from the manufacturer.

Wheel pan cover

Screw (scr 10-16)

10-16 pl pnp 5/8 szn - Sold individually.

Icemaker stripper arm (stripper im)

This part strips the ice from the icemaker mold during the ejection cycle. Used on rear mount icemakers.

Evaporator fan blade (blade evap fan asm)

This evaporator fan blade is for your refrigerator, and it circulates air so that the temperature of the fridge is regulated. This model has 3 blades, and is a little more than 4 inches in diameter. It is made of white plastic and is sold individually. If your refrigerator is noisy and you hear a clicking sound, it is a good indication that the evaporator fan blade is warped or damaged. If the fridge or freezer sections become too warm, the fan could be to blame as well.

Front dispenser bucket auger nut (nut auger frt disp)

Coarse thread

Crisper pan front gasket (gasket pan crv front)

This part is a replacement pan cover gasket for your refrigerator. You will find the pan cover gasket on the meat pan, and it helps to seal the pan. If the pan cover gasket is lost or damaged, it will not be able to create the seal and will need to be replaced. The gasket is approximately 15 inches wide and is white in color. It is an OEM part from the manufacturer and is sold individually.

Evaporator fan grommet - grey (grommet evap fan)

This is a replacement evaporator fan grommet for your refrigerator. The fan grommet absorbs the vibration from the evaporator fan motor for quiet operation while it runs. If your evaporator fan is unusually noisy, it could be because the grommet is damaged. This grommet is made of grey plastic and is approximately one inch in diameter. To access the fan grommet and complete this repair, you will need to remove the evaporator fan motor assembly. This part is sold individually.

Dc condenser fan motor - 12v (motor dc cond fan)

This fan motor circulates the air through the refrigerator grille and cools the compressor and condenser coils. It also helps to evaporate extra water in the drain pan.

Humidity control - white (humidity control)

This part regulates the humidity of your crisper bins. It does so by opening and closing vents on the bin. If your humidity control is broken or missing, you will need to replace it. This is a genuine OEM part from GE and is sourced directly from the manufacturer.

Ice bucket and auger assembly (bucket and auger asm)

This assembly includes the auger, bucket, cutting assembly (blades) and cover.

Ice dispenser solenoid service kit (solenoid & arm asm)

This kit includes 1 cube solenoid, 1 armature, 2 tooth washers and 2 1/4 hex head screws.