PDW8500JB GE Dishwasher Parts List

Sump (sump inlet)

This works in conjunction with the pump and filtration system. It is used to receive drainage for disposal.

Door handle actuator

This is a handle actuator for your dishwasher. It is made of black plastic, and is sold individually. The handle actuator is found in the control panel, and it releases the door latch when you lift the handle. If your current handle actuator is cracked or broken, you may not be able to open your dishwasher door, or the door will not close properly. The dishwasher also may not be able to start, and if this is the case, you will need to replace this part.

Cage roller bearing assembly (cage and roller bearing assembly)

Aides with movement or sliding of the dishrack.

Pump connector (connector pump assy)

The circulation pump adapter, or pump adapter assembly connects the circulation pump to the tub of your dishwasher. If your dishwasher is leaking around this adapter, check the connection to ensure everything is fitted tightly. If there is a problem with the adapter, make sure to disconnect the water supply to your dishwasher before completing the repair.

Impeller and seal kit (motor shaft seal and impeller kit)

This part helps stop your dishwasher from leaking. This kit includes the impeller, seal, blade, filter, skidder and skidder holder.

Fine filter (filter fine asm)

This filter sits at the bottom of the dishwasher.

Fine filter hub nut (nut hub, fine filter)

This is the replacement fine filter hub nut for your dishwasher. It is made of white plastic and is approximately 3 inches in diameter. The fine filter hub nut is also known as the lower spray arm hub nut, and it connects the lower spray arm to the hub. If the hub nut breaks, it can cause the spray arm to wobble during operation and this can result in a strange noise. To replace this part, first remove the spray arm by turning it counter clockwise, then do the same with the hub nut. Install the new hub nut by turning it counter clockwise, then replace the lower spray arm. This part is sold individually and is an OEM part from the manufacturer.

Upper spray arm bearing

This is the upper spray arm bearing for your dishwasher. The spray arm fits onto the spray arm bearing, which allows it to spin during the cycle. If your dishwasher is not cleaning dishes properly, or is making a lot of noise during operation, it could be the result of a damaged spray arm bearing. This part is made of white plastic and is approximately 1 inch long and 1/2 inch wide. This part is sold individually and is a genuine OEM part from the manufacturer.

Tine retainer/clip (retainer comb)

Used to hold the tine row or combs in place on the dishwasher rack. *** Sold Individually.

Screw

Size: 10-32 GXTT FLP .595 Sold individually.

Check valve flapper (check flapper valve, pump inlet)

This part allows the water to flow in the drain direction only and prevents the dirty water from coming back into the tub.

Lower spray arm bearing (spray arm bearing, lower)

This part is a replacement lower spray arm bearing for your dishwasher. It is made of gray plastic and is approximately ½ inch in diameter. The spray arm bearing reduces friction and allows the spray arm to rotate during the operating cycle. If the spray arm is not rotating or cleaning dishes properly, or the dishwasher is noisy during operation, you may need to replace the spray arm bearing. This is a bearing for the middle spray arm, which is mounted to the bottom of the upper dish rack. The bearing is made of metal and is approximately one inch in diameter. This part is sold individually and is an OEM part.

Hinge cable pulley (pulley, hinge cable)

Aids in the opening and closing of the dishwasher door.

Drain hose

This drain hose is an OEM, manufacturer-approved replacement part for your dishwasher. The drain hose filters out the wastewater from the dishwasher. If there is a hole in it, water will leak out of your dishwasher. Shut off the water and power to the unit before beginning this repair. Accessing the drain hose involves unscrewing the dishwasher and pulling it out. Remove the clamp holding the hose in place to its connection under the sink, using a 5/16ths socket. Disconnect the fill line. Use a 1/4 inch nut driver to loosen the clamp at the other end of the drain hose. Keep a towel handy for any water still inside. Keep the clamps for use on your new drain hose. Reinstall all hoses and lines in reverse order.

Scr 8-18 ab tsq 5/8 stainless steel (scr 8-18 ab tsq 5/8 ss)