RSD Parts List

Replacement ice maker (sub r0156669)

This is a replacement ice maker assembly. The ice maker receives water from the water inlet valve and will freeze until ice cubes are formed. Once the water has been frozen the cubes will be ejected from the mold in to the ice bucket. The ice maker will continue the process until the ice bucket has reached the limit. If your ice maker is not making ice you may need to replace this part. Disconnect the power and water supply before starting your repair. This ice maker is a genuine OEM part. NOTE: This part has been updated by the manufacturer and does not include the cover, ice level arm or the wire harness. You can reuse those from the original ice maker.

Light bulb - 40w (40 watt frosted appliance light bulb.)

This 40-watt light bulb has a standard screw-in base. It is used in many different appliances. If your current bulb is burnt out or broken you will need to replace it. This light bulb is a genuine OEM part and is sold individually.

Screw

Sold individually.

Condenser fan motor kit (refrigerator condenser fan motor kit, 2 watts clockwise rotation, hardware and instructions included. The condenser fan motor draws air though the con)

This condenser fan motor is used with frost-free refrigerators with a condenser coil. When the compressor runs, so does this fan, circulating air through the refrigerator grille, cooling the compressor and condenser coils. This part also helps to evaporate excess water in the drain pan. If your refrigerator/freezer section is too warm you may need to replace this part. This is a genuine OEM part. Please remember to disconnect the power to your refrigerator before starting the repair.

Door shelf retainer

Sold Individually.

Capacitor (capacitor, run)

The run capacitor is attached to the compressor. This part helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer. If your refrigerator is too warm, will not start, or your freezer section is too warm, you may need to replace this part. This is a genuine OEM part. Please remember to disconnect power to your refrigerator before starting your repair.

Flat style oven igniter (kit, ignitor-bake/bro)

This part is used to ignite the gas to light the oven burner in your range. If your oven is not heating, check the igniter to make sure it is glowing. If the igniter is glowing and your oven is not heating, your igniter is not strong enough to heat the oven and you will need to replace it. When replacing the igniter, be very careful not to touch the black element part of the igniter as it is very fragile. You will need to reuse the original bracket when installing the new igniter.

Refrigerator door switch (switch, light)

Door switch turns the light off when you close the door.

Thermal cut-off fuse kit (high-limit thermostat. If the dryer overheats, the high-limit thermostat cuts off power to the dryer. If the dryer won't heat, the high-limit thermost)

Crisper drawer shelf support (sub 67764-1)

This crisper drawer shelf support is used for many refrigerators.

Screw (screw 8 x 1/2)

This screw is half an inch long. It is made of metal and is intended for use with ranges, refrigerators, and washing machines.

Door shelf retainer bar - cut-to-fit (sub 70111-108)

This cut-to-fit door shelf retainer bar is twenty-six and a half inches long. It is all white in color and it is made of metal.

Defrost heater - 500w 115v (sub 61001846)

This set includes two nine and a quarter inch radiant glass defrost heaters joined together with wire. Each heater carries 500 watts and 115 volts. The defrost heater heats the evaporator in the defrost mode of operation to keep the cooling coils from frosting over.

Svc-set grate supportpad kit;66916,erd36 (burner grate support pads, set of 4.)

The rubber feet, also known as the burner grate foot, is used on the bottom of gas burner grates for a range and cooktop. The rubber feet help the grates sit on the top of a burner cap properly and works to keep it leveled. This way you can place your pans and pots on an even surface. This part also prevents your burner grates from scratching and damaging the top of your stove. This can lead to friction and the paint on the stove top can chip. Make sure to unplug range from power source before installing this part.

Hose clamp

This hose clamp expands from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag washing machines to secure the end of the drain hose to the pump drain port. Please make sure to disconnect the power to your washer before you start your repair. This hose clamp is a genuine OEM part and is sold individually.