Parts for Kenmore Models WDSR2080DC

Compression ring (ring compression)

Used in conjunction with the timer dial knob assembly.

Easy Part #:: EAP652828

Availability:: In Stock

Price:: $18.01

Hub washer

This is a replacement hub washer for your washing machine. If your washer is noisy, leaking, shaking, or pumping without spinning, you may need to replace the hub washer. The hub washer is found under the washer tub, beneath the split ring. You will need to remove the tub to access it. Before doing so you should disconnect the power and water sources from washer. The washer is made of metal and is a little more than an inch in diameter. It is sold individually, and is an OEM part.

Easy Part #:: EAP271511

Availability:: In Stock

Price:: $8.66

Knob and clip (knob & clip asm bq)

This knob accepts a D-shaped shaft.

Easy Part #:: EAP268450

Availability:: In Stock

Price:: $17.28

Lid switch with wire harness (lid switch asm)

The pin on the lid pushes on the lever of the lid switch to tell the machine that the lid is closed.

Easy Part #:: EAP1482372

Availability:: In Stock

Price:: $42.21

Pump to tub inlet drain hose (hose drain inlet(tub to))

This replacement inlet drain hose connects your washer's water pump to its tub. This hose is seven and a half inches in length and only two inches wide.

Easy Part #:: EAP11721808

Availability:: In Stock

Price:: $15.96

Knob dial (dial asm)

This part is a replacement knob dial for your washer. The knob dial rotates and allows you to select your desired settings. It is a round piece of white plastic with a small, triangular gray arrow on it. The knob dial is 3 inches in diameter and is sold individually. The control knob that attaches to it is sold separately. If your knob dial is worn, loose, or damaged, it may need to be replaced.

Easy Part #:: EAP756514

Availability:: In Stock

Price:: $34.50

Water pressure switch hose (pressure switch hose)

This is a water pressure switch hose, also known as the air dome tube, for your washer. It is made of clear plastic and is sold individually. The hose transports water to your water pressure switch, so the switch can control how much water enters the washer during a cycle. If your washer will not fill up with water, or if water continues to fill the tub even after it is full, you may have a damaged water pressure switch hose. Inspect the hose for cracks and leaks, and if the hose is damaged you will need to replace it.

Easy Part #:: EAP272183

Availability:: In Stock

Price:: $10.26

Inner tub base hub (hub)

This part is the replacement inner tub base hub for your washer. It is made of metal and is approximately 15 inches in diameter. The inner tub base hub fits between the wash tub and the spin basket, and it holds the spin basket on the gear case shaft. The main reason you would want to replace the hub, is if the washer will not agitate, or if you notice excessive noise or shaking when the washer is in use. Be sure to disconnect the washer from the water and power sources before you begin this repair. This part is sold individually and is and OEM part from the manufacturer.

Easy Part #:: EAP273296

Availability:: In Stock

Price:: $81.27

Shaft and mode shifter assembly (shaft and tube asm)

Also known as the gearcase or transmission. This part helps move the agitator back and forth during the wash cycle. New shifter mounting holes are NOT threaded, use original self tapping screws to install new part. Tub seal is included with assembly.

Easy Part #:: EAP2354082

Availability:: In Stock

Price:: $228.42

Socket rod support - white (suspension rod support)

This part is a replacement socket rod support for your washer. The socket rod support is found at the top of the washer frame in the front part of the washer. It supports the suspension rod, so the rod can prevent the tub from shaking too much during operation. If your washer is shaking excessively or emitting an odd sound during use, it may be because the rod support is broken, and the suspension rod is not able to do its job. This part is made of white plastic and is sold individually.

Easy Part #:: EAP268394

Availability:: In Stock

Price:: $10.91

Water level pressure switch (switch pressure)

This switch keeps your washer from overflowing. It is responsible for shutting off the power to the fill valve and redirects the power to the timer to start the washing machine running once the correct water level has been reached.

Easy Part #:: EAP269790

Availability:: In Stock

Price:: $48.50

Temperature switch - 3 position (switch rotary temp.)

Also known as a Rotary Switch. This part regulates the temperature of the water in the tub.

Easy Part #:: EAP3499718

Availability:: In Stock

Price:: $23.20

Suspension rod and spring assembly (suspension rod and spring assembly, black)

This part is the replacement suspension rod and spring assembly for your washer. The rod is approximately 27 inches long and is sold individually. The suspension rod and spring works something like a shock absorber and prevents the washer tub from shaking too much while the washer is operating. If you notice excessive shaking or vibrating, or if you notice a strange sound while the washer is running, you may need to replace the suspension rod and spring assembly. This is an OEM part sourced directly from the manufacturer.