YOUR ORDER SHIPS THE SAME DAYOn in-stock orders placedbefore 4pm Eastern Time.
Search by part or model number
Every model has its own, specific solutions. If you go to a car mechanic they'll need to know the exact make and model of your car to find the right repair parts. Appliances are the same.
See this guide for help.
Don't let a broken Amana appliance ruin your day. Repair your appliance with parts from EasyApplianceParts.com. We offer low prices, award winning service and same day shipping on all Amana appliance parts to help you repair any of your home appliances.
Easy Part #:
In Stock - Ships Today
NOTE: This replacement ice maker mechanism does NOT come with a cover,shut off arm, a wire harness, or the mounting hardware. Must be ordered separately.
This condenser fan motor operates in a clockwise fashion and carries carries 2W and 115V. It comes with screws, a blade mounting nut, and a cushion. This part provides forced-air cooling for the condenser coil.
This screw is sold individually.
This screw is sold individually
This gas dryer ignition coil set comes with two ignition coils: one three terminal Boost/Hold coil, and one two terminal secondary coil. Usually only one of them burns out but you should replace them as a set. Both have to be operational for the gas valve to open.
Sold individually. The size of this screw is 1/4" hex head and 10-12 x 1/2".
This part helps with the closing of the door and helps keep them in position.
This newer-style terminal block kit includes two metal brackets, two pre-crimped wires with terminals, two ceramic wire nuts, a heat shrinking tube, and a mounting screw.
This roller is for square-ported models and has a metallic bearing in its center. They are sold individually and most dryers use 2 rollers at the rear and it is recommended to replace both at the same time.
At 93-3/8" in length, this flat dryer drum belt has 5 ridges and is 3/8" wide.
This drum glide is sold individually. ***Please Note: these should be replaced in pairs.
This part has been substituted by the manufacturer and has a hole in the center. It no longer has a solid bottom. Sold individually.
This part helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer.
This part has a high-quality carbon filter that reduces contaminants. Replace the filter annually or when the filter light is on. Sold individually.
This hose clamp is sold individually.
This roller pin is used with a refrigerator's roller.
This wheel is sold individually - purchase quantity needed.
A dryer's idler pulley wheel serves to help the belt to rotate the drum.
Also known as Wheel.
This part is used to help tell the icemaker what to do - it turns the timing cams and the ejector blades. Motor is not sold separately.
This part senses the flame for heat allowing the gas valve to open.
1/4" Plastic tubing, 8 1/2 feet long.
This eight-hour defrost timer will replace most other defrost timers. This device acts like a clock. It continually advances and alternates between activating the cooling cycle and the defrost heater. The best way to make sure you get the correct timer for your refrigerator is to conduct a search for your model number.
This dryer drum belt has four ridges, three grooves and is 1/4" wide.
The top of this part is now black.
The timer will shut off the cooling system of the refrigerator and the defrost heater will turn on.
This motor assembly has a threaded shaft and includes the pulley. NOTE: The pulley is only available with the motor and is not sold separately.
This cap is white in color and is made of plastic. This end cap is used in a refrigerator's icemaker.
Sold individually. This bulb is a 7 watt appliance incandescent light bulb.
The water inlet valve is a solenoid-operated switch located at the bottom of the refrigerator. When it is energized by electrical power, water is released from the supply line through the water valve and into the compact icemaker mold.
***Please NOTE: This part has been redesigned and may appear different than the original. It has a new quick connection. To install: cut the retaining nut off the existing water line and gently push into new valve. To remove: depress the ring that the tube slides into.
This kit comes in two pieces: the catch and the clip.
Part may differ in appearance, but functions same as original.
This part is used on the front dryer drum glides.
Used with Evaporator Fan Motors.