YOUR ORDER SHIPS THE SAME DAYOn in-stock orders placedbefore 4pm Eastern Time.
Search by part or model number
Every model has its own, specific solutions. If you go to a car mechanic they'll need to know the exact make and model of your car to find the right repair parts. Appliances are the same.
See this guide for help.
Don't let a broken Amana Dryer ruin your day. Repair your Dryer with parts from EasyApplianceParts.com. We offer low prices, award winning service and same day shipping on all Amana Dryer parts to help you repair any of your home appliances.
This gas dryer ignition coil set comes with two ignition coils: one three terminal Boost/Hold coil, and one two terminal secondary coil. Usually only one of them burns out but you should replace them as a set. Both have to be operational for the gas valve to open.
Easy Part #:
In Stock - Ships Today
This roller is for square-ported models and has a metallic bearing in its center. They are sold individually and most dryers use 2 rollers at the rear and it is recommended to replace both at the same time.
At 93-3/8" in length, this flat dryer drum belt has 5 ridges and is 3/8" wide.
This drum glide is sold individually. ***Please Note: these should be replaced in pairs.
A dryer's idler pulley wheel serves to help the belt to rotate the drum.
This part senses the flame for heat allowing the gas valve to open.
This dryer drum belt has four ridges, three grooves and is 1/4" wide.
This screw is sold individually.
This kit comes in two pieces: the catch and the clip.
This motor assembly has a threaded shaft and includes the pulley. NOTE: The pulley is only available with the motor and is not sold separately.
This part is used on the front dryer drum glides.
The spring for this part is sold separately.
This part replaces older two terminal switches.
Note: This part no longer comes with the felt seal. This filter collects lint as it passes through the dryer vent.
This front cover spring retaining clip is not quite an inch long. It is made entirely of metal and is used for some washing machines.
Part may differ in appearance, but functions same as original part.
Meant as a backup to a high limit thermostat, this fuse is typically set to trip at a higher temperature than that of a high limit thermostat. This is a one-time use fuse, so when it does trip, you do need to replace it. It's letting you know that something is wrong with your dryer.
These brackets support each side of the tub. Order quantity needed.
This shaft is made to fit the center of the idler pulley wheel of your dryer.
A door switch is a simple on/off mechanism that prohibits the dryer from operating when the door is open.
This part includes the upper and lower air duct assembly and lint screen.
Cycling thermostats continually cycle the heating element off and on to maintain a constant inner temperature. This particular cycling thermostat has a limit of 155 degrees Fahrenheit and a differential of 25 degrees. Meaning that with this thermostat, the heating element will cut out at 155 degrees and cycle back on once the internal temperature drops by 25 degrees.
This clothes dryer thermal cut-off kit includes one high limit thermostat with a limit of 250 degrees Fahrenheit, and one thermal cut-off fuse (309 degrees). This kit also includes flat heaters with jumper wires.
This part is a one-time use thermal fuse which attaches to the blower wheel housing of your clothes dryer. It cannot be re-set and must be replaced when continuity between the pins is no longer present. Terminal size is 3/16".
Sold individually. This bulb is a 7 watt appliance incandescent light bulb.
Sold individually. The size of this screw is 1/4" hex head and 10-12 x 1/2".
This hi-limit thermostat acts as a safety mechanism that keeps the dryer from overheating. With this thermostat, a dryer's heating element will cut out if the internal temperature reaches 225 degrees Fahrenheit. The element will kick back in when the temperature drops to 185 degrees Fahrenheit - the differential of 40 degrees.
This motor fits most Whirlpool incorporated dryer brands before 1996. NOTE: Pulley is NOT available separately.
This silicone carbide igniter with ceramic holder kit includes the 3" flat igniter, bracket, 5" wire leads, and the plug. Able to replace both round and flat igniters, this kit is used for many gas clothes dryers.
This arm is what attaches to the idler pulley wheel.
This hi-limit thermostat with Terminal Extension Arm acts as as safety mechanism that keeps the dryer from overheating. Once the dryer temperature reaches 221 degrees Farenheit, this piece will shut down power to the heating element until it drops by 80 degrees Farenheit.
This element is strung with a coiled wire made of a nickel and a chrome alloy. This wire receives, but resists, a controlled electric current and as a result, the wire heats up. The heat produced is used to dry the clothes in your dryer.
This filter collects lint as it passes through the dryer vent.
These two drum support rollers are no longer available for individual sale. Available in a package of two and it is recommended that you replace both rollers at once. These two rollers come with four tri-rings and one palnut.
This metal spring fits onto the arm of the idler pulley assembly.
This orange dot heating element replaces those elements with an orange dot on the element flange.
This kit is used for electric clothes dryers, and it comes with a yellow wire nut.
This cycling thermostat has a limit of 153 degrees Fahrenheit, meaning that your dryer will cut out when the internal temperature reaches 153 degrees. It kicks back in when the temperature drops by 15 degrees Fahrenheit.