YOUR ORDER SHIPS THE SAME DAYOn in-stock orders placedbefore 4pm Eastern Time.
Search by part or model number
Every model has its own, specific solutions. If you go to a car mechanic they'll need to know the exact make and model of your car to find the right repair parts. Appliances are the same.
See this guide for help.
Don't let a broken Dryer ruin your day. Repair your Dryer with parts from EasyApplianceParts.com. We offer low prices, award winning service and same day shipping on all Dryer parts to help you repair any of your home appliances.
This dryer drum belt has four ridges, three grooves and is 1/4" wide.
Easy Part #:
In Stock - Ships Today
This part is a one-time use thermal fuse which attaches to the blower wheel housing of your clothes dryer. It cannot be re-set and must be replaced when continuity between the pins is no longer present. Terminal size is 3/16".
This gas dryer ignition coil set comes with two ignition coils: one three terminal Boost/Hold coil, and one two terminal secondary coil. Usually only one of them burns out but you should replace them as a set. Both have to be operational for the gas valve to open.
This dryer door latch kit comes with one plastic door latch and one metal door strike.
This drum support roller includes one drum roller and two bearings. Most dryers use two drum rollers, and is recommended to change both at once.
Sold individually. There are 2 per dryer. They attach to the outer-most sides of the bearing. Manufacture recommends to replace both slides at the same time.
There are 2 per dryer. They attach to the outer-most sides of the bearing. Manufacture recommends to replace both slides at the same time. Sold individually.
This motor fits most Whirlpool incorporated dryer brands before 1996. NOTE: Pulley is NOT available separately.
This part provides the tension required for a multi-ribbed belt. It also serves to help the belt to rotate the drum. This arm is what attaches to the idler pulley wheel.
This silicone carbide igniter with ceramic holder kit includes the 3" flat igniter, bracket, 5" wire leads, and the plug. Able to replace both round and flat igniters, this kit is used for many gas clothes dryers.
At 100" in length, this dryer drum belt is 3/8" wide and has 5 ridges. This is the belt that is from the tumbler to the main drive motor.
These two drum support rollers are no longer available for individual sale. Available in a package of two and it is recommended that you replace both rollers at once. These two rollers come with four tri-rings and one palnut.
This front glide kit comes with a blue plastic glide, a brown cork pad, and two metallic rivets. Two kits are required per appliance. Also, a rivet tool is required for this kit - purchase locally.
This screw is sold individually.
This kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high temperature lubricant and installation screws.
This roller shaft acts as the axel for the drum roller. Also known as drum roller axle.
This metallic screw is less than an inch long and comes with a plastic washer.
This element is strung with a coiled wire made of a nickel and a chrome alloy. This wire receives, but resists, a controlled electric current and as a result, the wire heats up. The heat produced is used to dry the clothes in your dryer.
This rear drum bearing kit comes with a shaft, bearing and installation instructions. The bearing plate comes with a slot in it for the ground strap. Helps keep your dryer running as smoothly as possible with as little noise as possible.
This part is sold individually.
A door switch is a simple on/off mechanism that prohibits the dryer from operating when the door is open.
Cycling thermostats continually cycle the heating element off and on to maintain a constant inner temperature. This particular cycling thermostat has a limit of 155 degrees Fahrenheit and a differential of 25 degrees. Meaning that with this thermostat, the heating element will cut out at 155 degrees and cycle back on once the internal temperature drops by 25 degrees.
This part senses the flame for heat allowing the gas valve to open.
This element carries 5200W and 240V.
Note: This element no longer includes two terminals and two adapter leads. They must be ordered separately.
This clothes dryer thermal cut-off kit includes one high limit thermostat with a limit of 250 degrees Fahrenheit, and one thermal cut-off fuse (309 degrees). This kit also includes flat heaters with jumper wires.
This filter collects lint as it passes through the dryer vent.
Cycling themostats continually cycle the heating element off and on to maintain a constant inner temperature within the dryer. This particular cycling thermostat can be adjusted between 135 and 155 degrees Fahrenheit. The differential of this thermostat is 20 degrees, meaning that with this thermostat, the heating element will cycle back on once the internal temperature drops by 20 degrees.
A dryer's idler pulley helps the belt to rotate the drum. Also known as dryer belt tension pulley wheel.
This drive belt is 89.5" long.
This comes with a metallic hub clip to hold it firmly in place.
Sold Individually. Most dryers require 2. Tri-rings sold separately.
This idler pulley shaft washer is used with many clothes dryers. It is less than an inch long, and it is black in color. Sold individually.
This 87-3/4" long dryer drum belt goes around the dryer drum and the pulley to rotate the drum once motor is activated.
This dryer drum belt from Whirlpool/Kenmore has five ridges. It is used for many of Whirlpool's brands of clothes dryers. This flat belt is 1/4 of an inch wide.
The blower wheel is a squirrel cage type wheel whose purpose is to move the air through the room or appliance.
This kit is used for electric clothes dryers, and it comes with a yellow wire nut.
This kit is simple on/off mechanism that prohibits the machine from operating when the door is open.