Dryer Hardware

Roller Support Tri-Ring

Part Number: WPW10512946

The tri ring is used to hold the drum support rollers or the idler pulley onto the shaft. If your dryer will not tumble or is noisy, you may need to replace the tri ring. This is a genuine OEM part and is sold individually.

Igniter Kit

7 Reviews

Part Number: 279311

This silicon carbide igniter with ceramic holder kit includes the 3-inch flat igniter, mounting bracket, 4-inch wire leads, and the plug. It can replace both round and flat igniters. This kit is used for many gas clothes dryers. This part ignites the gas within the dryer to heat the dryer during the cycle, so if your dryer takes too long to dry, has no heat or not enough heat, you may need to replace the igniter. Be sure to disconnect the power source from your dryer before you do this repair. The igniter is very fragile and should be handled with care.

Retaining Ring

Part Number: WP9703438

The retaining clip goes onto the end of the roller axle and holds the drum roller on to the axle. If the ring is broken or damaged, you will need to replace it. This is a genuine OEM part and is sold individually.

Screw

Part Number: WPW10661886

This mounting screw is a genuine OEM replacement part for the door handle in your refrigerator. If you are having trouble shutting the refrigerator door, or opening it, replacing this screw can help solve the issue. Replacing this part is easy and requires minimal disassembly of the refrigerator end cap handle. Your will need a screwdriver to complete this repair.

D-Shaped Knob Clip

Part Number: WH01X10106

This control knob clip helps secure the timer knob to the shaft allowing you to select the desired setting for your dryer. If the knob has become loose or the clip is missing you will need to replace the clip. This clip is a genuine OEM part, made of metal and is sold individually.

Lid Bumper

Part Number: WR02X10540

This orange rubber bumper prevents the condenser fan motor from bumping against the mounting bracket every time the fan motor starts. If your refrigerator/freezer is noisy, the bumper could be worn down or missing, and the sound could be a result of the motor scraping the side bracket. You will find it between the fan motor and the side bracket on the evaporator fan motor assembly. It has a rounded top and a slightly pointed bottom. The bumper is a genuine OEM part and is sold individually.

Single Front Panel Cip

1 Review

Part Number: W10854425

This part is the replacement single front panel clip for your dryer. It is made of metal and is approximately 2 inches long and ¾ inch wide. The front panel retainer clip is what holds the front panel on to the dryer. If the clip is damaged or missing, or if the front panel appears loose, you may need to replace the clip. This part is sold individually and is an authentic OEM part.

Thrust Washer

Part Number: WP233520

This part is located between the drum support rollers and idler pulley in your dryer to help prevent the parts from bumping up against the brackets they are attached to. If your dryer has a burning smell, is noisy, or will not tumble, you may need to replace the thrust washer. The washer is 3/4 inches in diameter and a is genuine OEM part. It is recommended to disconnect the power to your dryer before you start your repair.

Drum Roller Shaft Washer

Part Number: WP312535

This roller shaft washer is just under an inch in diameter and is used for some Whirlpool brand clothes dryers. It is located on the drum support roller shaft. If your dryer is noisy or will not tumble, you may need to replace the roller shaft washer. This is a genuine OEM part. Please remember to disconnect the power supply to your dryer before you start your repair. Sold individually.

Idler Pulley Shaft Washer

Part Number: WPY312527

This idler pulley shaft washer is used with many clothes dryers and is located between the idler pulley and the bracket. If the idler shaft washer is worn it will cause the washer to rub against the e-clip and bracket which will cause a squeaky noise and will need to be replaced. This part is sold individually and there are two required for each roller. The idler shaft washer is less than an inch long, and it is black in color. Please remember to disconnect the power to your dryer before starting the repair.