RSG Parts List

Evaporator fan blade (blade evap fan asm)

This evaporator fan blade is for your refrigerator, and it circulates air so that the temperature of the fridge is regulated. This model has 3 blades, and is a little more than 4 inches in diameter. It is made of white plastic and is sold individually. If your refrigerator is noisy and you hear a clicking sound, it is a good indication that the evaporator fan blade is warped or damaged. If the fridge or freezer sections become too warm, the fan could be to blame as well.

Dispenser housing shield (housing shield disp)

This part helps to contain parts for the ice and water dispenser. The overlay and dispenser board is attached on the front of the housing shield.

Package of 12 screws (scr 8-18 ab rndw 5/8 ss)

This is a package of twelve Phillips-head screws. They can be used as replacement screws in refrigerators, ice makers, or freezers. Be sure to check that your appliance model is compatible with these screws. The screws are approximately ¾ of an inch in length.

Handle mounting screw (door handle mounting post)

Front dispenser bucket auger nut (nut auger frt disp)

Coarse thread

Crisper drawer front gasket (gasket pan cover frt)

This part is the replacement crisper drawer front gasket for your refrigerator. It is white in color and is approximately 16 inches long and ¾ of an inch wide. The gasket helps create a seal for your crisper drawer. If it is worn out, damaged, or missing, it may be difficult to create the seal on the front of the crisper drawer. Your refrigerator has one gasket per crisper drawer, so there may be more than one in the refrigerator itself. This part is sold individually, so be sure to check both gaskets if you suspect one is worn out. This is an OEM part sourced directly from the manufacturer.

Evaporator fan motor kit

The evaporator fan motor is in the back of the freezer section and circulates air over the refrigerator coils. These coils will convert the heat into cool air, which then circulates the cold air from the freezer section to the fresh food section. It is suggested to replace the thermistor when replacing the evaporator fan. This is a genuine OEM part. Please remember to disconnect the power to the refrigerator before starting your repair.

Water filter

A good way to judge whether the filter needs to be replaced is when the water flow to the dispenser starts slowing down and there has been no change to the water pressure to the product. There is no bypass needed. Just remove the filter and it will automatically bypass the water filter.

Freezer wire shelf (shelf fz)

This part is approx. 14 3 /4" L x 13 1/4" W. Sold individually.

Evaporator fan grommet - grey (grommet evap fan)

This is a replacement evaporator fan grommet for your refrigerator. The fan grommet absorbs the vibration from the evaporator fan motor for quiet operation while it runs. If your evaporator fan is unusually noisy, it could be because the grommet is damaged. This grommet is made of grey plastic and is approximately one inch in diameter. To access the fan grommet and complete this repair, you will need to remove the evaporator fan motor assembly. This part is sold individually.

Door handle bottom end cap - white (tail handle sxs wh)

This end cap is connected to the bottom of the fridge/freezer door handle.

Dc condenser fan motor - 12v (motor dc cond fan)

This fan motor circulates the air through the refrigerator grille and cools the compressor and condenser coils. It also helps to evaporate extra water in the drain pan.

Mwf bypass (auger asm disp)

This part is a replacement filter bypass cap for your refrigerator. If you intend to use an external water filtration system for your refrigerator, the bypass cap will allow you to do so. To use a filter bypass cap, simply screw it in where you would normally screw in the regular water filter. If you have a bypass system installed and your ice maker doesn’t make ice, your water dispenser doesn’t make water, or if there is water dripping inside your refrigerator, you may need to replace the bypass filter cap. This part is made of white plastic and is sold individually.

Evaporator fan with thermistor (motor dc evap fan)

This evaporator fan motor is located in the back of the freezer, and circulates air over the refrigerator coils. These coils will convert the heat into cool air, which is then circulated. The thermistor snaps on to the top portion of the evaporator. The thermistor sends the evaporator temperature signals to the main control board. The thermistor must be replaced when replacing the evaporator fan.

Hexagonal screw (door hinge bracket screw)

Sold individually.