NA Parts List

Motor with pulley (pulley)

This motor is a 2 speed, 1/2 HP, 120V, 60Hz.

Lid hinge mounting screw (screw, 6-32x.340 flat)

Sold individually. NOTE: The color on the screw may not be the same as the image, but will still function the same.

Spin belt

This v-shaped spin belt helps transfer power from the motor to the transmission to help pump the water in and out of the washer. It also helps runs the spin cycle in the washer.

Snubber ring (snubber)

The snubber ring works in conjunction with your washing machine by helping to reduce noise and vibration during operation. The snubber ring fits between the leg and washer base. It is white in color, and measures approximately 8 1/2” in diameter. If your washer is making a loud noise or shakes a lot during use, the snubber ring may need to be replaced. Disconnect the power and water supply before beginning your repair. This is a genuine OEM part.

Transmission pulley and bearing kit (thrust bearing kit)

The transmission pulley and bearing kit, also known as a thrust bearing kit, is located on the drive shaft. If your washer won’t agitate during use, drum won’t drain, or there is a loud noise during operation, you may need to replace this part. A worn bearing also causes slow spinning or no spin at all. This kit includes the pulley that rotates to spin the tub, washer, and thrust bearing that fits between the pulley and the transmission shaft, 2 upper race washers, 1 lower race washer and the instruction sheet. This is a genuine OEM kit; the parts are not available separately. Please remember to disconnect the power and water supply to the washer before starting the repair.

Hose clamp (sub 25-7867)

This hose clamp expands from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag washing machines to secure the end of the drain hose to the pump drain port. Please make sure to disconnect the power to your washer before you start your repair. This hose clamp is a genuine OEM part and is sold individually.

15" compactor bag carrier with easy grip handles (compactor bag carrying caddy)

The compactor bag carrier is located under the plastic trash bag. It will fit around a trash compactor bag inside a 15” compactor and helps making removing the trash bag from the compactor easier with the easy grip handles. This carrier is bisque in color and measures 8” wide x 16” high x 11” deep. You should replace the bag carrier if it is damaged or missing. This is the bag carrier only, compactor bags are not included, they must be ordered separately. This is a genuine OEM part.

Screw (sub 25-7759)

This screw is sold individually.

Screw-in plastic leveling leg (leveling leg)

Sold individually.

Adjustable leveling leg (sub 40039001)

The adjustable leveling leg is used to support and keep your washer level. If your washer shakes and moves during cycles you may need to replace the leveling leg. The stop nut is included with the leveling leg. The rubber foot is not included, it must be ordered separately. Order the quantity you need as they are sold individually. This is a genuine OEM part.

Water inlet valve (water inlet valve. The water inlet valve opens to allow hot, cold or warm water to enter the washing machine.)

This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed. If your washer will not stop filling with water, is leaking, or will not fill with water, you may need to replace the water inlet valve. Please make sure to disconnect the power to your washer before you start your repair. This water inlet valve is a genuine OEM part.

Spring retaining clip (sub 56080)

This spring retaining clip is used to hold the front panel onto the top of the washer. If your front panel is loose you might need to replace the clip. The clip is made entirely of metal and is used for some washing machines. This part is not quite an inch long and is sold individually. This is a genuine OEM part.

Idler pulley wheel

This wheel has a center metallic bearing. A dryer's idler pulley wheel serves to help the belt to rotate the drum.

Cover screw (screw)

Sold individually.

Agitator auger and post assembly